The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

geom (4)
  • >> geom (4) ( FreeBSD man: Специальные файлы /dev/* )
  • geom (4) ( Русские man: Специальные файлы /dev/* )
  • geom (8) ( FreeBSD man: Команды системного администрирования )
  • Ключ geom обнаружен в базе ключевых слов.

  • BSD mandoc
     

    NAME

    GEOM
    
     - modular disk I/O request transformation framework
    
     
    

    DESCRIPTION

    The framework provides an infrastructure in which ``classes'' can perform transformations on disk I/O requests on their path from the upper kernel to the device drivers and back.

    Transformations in a context range from the simple geometric displacement performed in typical disk partitioning modules over RAID algorithms and device multipath resolution to full blown cryptographic protection of the stored data.

    Compared to traditional ``volume management'' differs from most and in some cases all previous implementations in the following ways:

    Being extensible means that new transformations are treated no differently than existing transformations.

    Fixed hierarchies are bad because they make it impossible to express the intent efficiently. In the fixed hierarchy above, it is not possible to mirror two physical disks and then partition the mirror into subdisks, instead one is forced to make subdisks on the physical volumes and to mirror these two and two, resulting in a much more complex configuration. on the other hand does not care in which order things are done, the only restriction is that cycles in the graph will not be allowed.  

    TERMINOLOGY AND TOPOLOGY

    is quite object oriented and consequently the terminology borrows a lot of context and semantics from the OO vocabulary:

    A ``class'' represented by the data structure Vt g_class implements one particular kind of transformation. Typical examples are MBR disk partition, BSD disklabel, and RAID5 classes.

    An instance of a class is called a ``geom'' and represented by the data structure Vt g_geom . In a typical i386 Fx system, there will be one geom of class MBR for each disk.

    A ``provider'' represented by the data structure Vt g_provider , is the front gate at which a geom offers service. A provider is Do a disk-like thing which appears in /dev Dc - a logical disk in other words. All providers have three main properties: ``name'' ``sectorsize'' and ``size''

    A ``consumer'' is the backdoor through which a geom connects to another geom provider and through which I/O requests are sent.

    The topological relationship between these entities are as follows:

    All geoms have a rank-number assigned, which is used to detect and prevent loops in the acyclic directed graph. This rank number is assigned as follows:

    1. A geom with no attached consumers has rank=1.
    2. A geom with attached consumers has a rank one higher than the highest rank of the geoms of the providers its consumers are attached to.

     

    SPECIAL TOPOLOGICAL MANEUVERS

    In addition to the straightforward attach, which attaches a consumer to a provider, and detach, which breaks the bond, a number of special topological maneuvers exists to facilitate configuration and to improve the overall flexibility.

    TASTING
    is a process that happens whenever a new class or new provider is created, and it provides the class a chance to automatically configure an instance on providers which it recognizes as its own. A typical example is the MBR disk-partition class which will look for the MBR table in the first sector and, if found and validated, will instantiate a geom to multiplex according to the contents of the MBR.

    A new class will be offered to all existing providers in turn and a new provider will be offered to all classes in turn.

    Exactly what a class does to recognize if it should accept the offered provider is not defined by , but the sensible set of options are:

    ORPHANIZATION
    is the process by which a provider is removed while it potentially is still being used.

    When a geom orphans a provider, all future I/O requests will ``bounce'' on the provider with an error code set by the geom. Any consumers attached to the provider will receive notification about the orphanization when the event loop gets around to it, and they can take appropriate action at that time.

    A geom which came into being as a result of a normal taste operation should self-destruct unless it has a way to keep functioning whilst lacking the orphaned provider. Geoms like disk slicers should therefore self-destruct whereas RAID5 or mirror geoms will be able to continue as long as they do not lose quorum.

    When a provider is orphaned, this does not necessarily result in any immediate change in the topology: any attached consumers are still attached, any opened paths are still open, any outstanding I/O requests are still outstanding.

    The typical scenario is:

    While this approach seems byzantine, it does provide the maximum flexibility and robustness in handling disappearing devices.

    The one absolutely crucial detail to be aware of is that if the device driver does not return all I/O requests, the tree will not unravel.

    SPOILING
    is a special case of orphanization used to protect against stale metadata. It is probably easiest to understand spoiling by going through an example.

    Imagine a disk, da0 on top of which an MBR geom provides da0s1 and da0s2 and on top of da0s1 a BSD geom provides da0s1a through da0s1e and that both the MBR and BSD geoms have autoconfigured based on data structures on the disk media. Now imagine the case where da0 is opened for writing and those data structures are modified or overwritten: now the geoms would be operating on stale metadata unless some notification system can inform them otherwise.

    To avoid this situation, when the open of da0 for write happens, all attached consumers are told about this and geoms like MBR and BSD will self-destruct as a result. When da0 is closed, it will be offered for tasting again and, if the data structures for MBR and BSD are still there, new geoms will instantiate themselves anew.

    Now for the fine print:

    If any of the paths through the MBR or BSD module were open, they would have opened downwards with an exclusive bit thus rendering it impossible to open da0 for writing in that case. Conversely, the requested exclusive bit would render it impossible to open a path through the MBR geom while da0 is open for writing.

    From this it also follows that changing the size of open geoms can only be done with their cooperation.

    Finally: the spoiling only happens when the write count goes from zero to non-zero and the retasting happens only when the write count goes from non-zero to zero.

    INSERT/DELETE
    are very special operations which allow a new geom to be instantiated between a consumer and a provider attached to each other and to remove it again.

    To understand the utility of this, imagine a provider being mounted as a file system. Between the DEVFS geom's consumer and its provider we insert a mirror module which configures itself with one mirror copy and consequently is transparent to the I/O requests on the path. We can now configure yet a mirror copy on the mirror geom, request a synchronization, and finally drop the first mirror copy. We have now, in essence, moved a mounted file system from one disk to another while it was being used. At this point the mirror geom can be deleted from the path again; it has served its purpose.

    CONFIGURE
    is the process where the administrator issues instructions for a particular class to instantiate itself. There are multiple ways to express intent in this case - a particular provider may be specified with a level of override forcing, for instance, a BSD disklabel module to attach to a provider which was not found palatable during the TASTE operation.

    Finally, I/O is the reason we even do this: it concerns itself with sending I/O requests through the graph.

    I/O REQUESTS
    represented by Vt struct bio , originate at a consumer, are scheduled on its attached provider and, when processed, are returned to the consumer. It is important to realize that the Vt struct bio which enters through the provider of a particular geom does not Do come out on the other side Dc . Even simple transformations like MBR and BSD will clone the Vt struct bio , modify the clone, and schedule the clone on their own consumer. Note that cloning the Vt struct bio does not involve cloning the actual data area specified in the I/O request.

    In total, four different I/O requests exist in : read, write, delete, and ``get attribute.''

    Read and write are self explanatory.

    Delete indicates that a certain range of data is no longer used and that it can be erased or freed as the underlying technology supports. Technologies like flash adaptation layers can arrange to erase the relevant blocks before they will become reassigned and cryptographic devices may want to fill random bits into the range to reduce the amount of data available for attack.

    It is important to recognize that a delete indication is not a request and consequently there is no guarantee that the data actually will be erased or made unavailable unless guaranteed by specific geoms in the graph. If ``secure delete'' semantics are required, a geom should be pushed which converts delete indications into (a sequence of) write requests.

    ``Get attribute'' supports inspection and manipulation of out-of-band attributes on a particular provider or path. Attributes are named by ASCII strings and they will be discussed in a separate section below.

    (Stay tuned while the author rests his brain and fingers: more to come.)  

    DIAGNOSTICS

    Several flags are provided for tracing operations and unlocking protection mechanisms via the kern.geom.debugflags sysctl. All of these flags are off by default, and great care should be taken in turning them on.

    0x01 (G_T_TOPOLOGY )
    Provide tracing of topology change events.
    0x02 (G_T_BIO )
    Provide tracing of buffer I/O requests.
    0x04 (G_T_ACCESS )
    Provide tracing of access check controls.
    0x08 (unused)
    0x10 (allow foot shooting)
    Allow writing to Rank 1 providers. This would, for example, allow the super-user to overwrite the MBR on the root disk or write random sectors elsewhere to a mounted disk. The implications are obvious.
    0x40 (G_F_DISKIOCTL )
    This is unused at this time.
    0x80 (G_F_CTLDUMP )
    Dump contents of gctl requests.

     

    HISTORY

    This software was developed for the Fx Project by An Poul-Henning Kamp and NAI Labs, the Security Research Division of Network Associates, Inc. under DARPA/SPAWAR contract N66001-01-C-8035 (``CBOSS'' ) as part of the DARPA CHATS research program.

    The first precursor for was a gruesome hack to Minix 1.2 and was never distributed. An earlier attempt to implement a less general scheme in Fx never succeeded.  

    AUTHORS

    An Poul-Henning Kamp Aq phk@FreeBSD.org


     

    Index

    NAME
    DESCRIPTION
    TERMINOLOGY AND TOPOLOGY
    SPECIAL TOPOLOGICAL MANEUVERS
    DIAGNOSTICS
    HISTORY
    AUTHORS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру