The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Поиск:  Каталог документации / Документация по FreeBSD / Руководства по FreeBSD на английском

29.3 System Calls

29.3.1 Default Calling Convention

By default, the FreeBSD kernel uses the C calling convention. Further, although the kernel is accessed using int 80h, it is assumed the program will call a function that issues int 80h, rather than issuing int 80h directly.

This convention is very convenient, and quite superior to the Microsoft convention used by MS DOS. Why? Because the Unix convention allows any program written in any language to access the kernel.

An assembly language program can do that as well. For example, we could open a file:

    kernel:
        int 80h ; Call kernel
        ret
    
    open:
        push    dword mode
        push    dword flags
        push    dword path
        mov eax, 5
        call    kernel
        add esp, byte 12
        ret

This is a very clean and portable way of coding. If you need to port the code to a Unix system which uses a different interrupt, or a different way of passing parameters, all you need to change is the kernel procedure.

But assembly language programmers like to shave off cycles. The above example requires a call/ret combination. We can eliminate it by pushing an extra dword:

    open:
        push    dword mode
        push    dword flags
        push    dword path
        mov eax, 5
        push    eax     ; Or any other dword
        int 80h
        add esp, byte 16

The 5 that we have placed in EAX identifies the kernel function, in this case open.

29.3.2 Alternate Calling Convention

FreeBSD is an extremely flexible system. It offers other ways of calling the kernel. For it to work, however, the system must have Linux emulation installed.

Linux is a Unix-like system. However, its kernel uses the same system-call convention of passing parameters in registers MS DOS does. As with the Unix convention, the function number is placed in EAX. The parameters, however, are not passed on the stack but in EBX, ECX, EDX, ESI, EDI, EBP:

    open:
        mov eax, 5
        mov ebx, path
        mov ecx, flags
        mov edx, mode
        int 80h

This convention has a great disadvantage over the Unix way, at least as far as assembly language programming is concerned: Every time you make a kernel call you must push the registers, then pop them later. This makes your code bulkier and slower. Nevertheless, FreeBSD gives you a choice.

If you do choose the Linux convention, you must let the system know about it. After your program is assembled and linked, you need to brand the executable:

    % brandelf -f Linux filename

29.3.3 Which Convention Should You Use?

If you are coding specifically for FreeBSD, you should always use the Unix convention: It is faster, you can store global variables in registers, you do not have to brand the executable, and you do not impose the installation of the Linux emulation package on the target system.

If you want to create portable code that can also run on Linux, you will probably still want to give the FreeBSD users as efficient a code as possible. I will show you how you can accomplish that after I have explained the basics.

29.3.4 Call Numbers

To tell the kernel which system service you are calling, place its number in EAX. Of course, you need to know what the number is.

29.3.4.1 The syscalls File

The numbers are listed in syscalls. locate syscalls finds this file in several different formats, all produced automatically from syscalls.master.

You can find the master file for the default Unix calling convention in /usr/src/sys/kern/syscalls.master. If you need to use the other convention implemented in the Linux emulation mode, read /usr/src/sys/i386/linux/syscalls.master.

Note: Not only do FreeBSD and Linux use different calling conventions, they sometimes use different numbers for the same functions.

syscalls.master describes how the call is to be made:

    0  STD NOHIDE  { int nosys(void); } syscall nosys_args int
    1   STD NOHIDE  { void exit(int rval); } exit rexit_args void
    2   STD POSIX   { int fork(void); }
    3   STD POSIX   { ssize_t read(int fd, void *buf, size_t nbyte); }
    4   STD POSIX   { ssize_t write(int fd, const void *buf, size_t nbyte); }
    5   STD POSIX   { int open(char *path, int flags, int mode); }
    6   STD POSIX   { int close(int fd); }
    etc...

It is the leftmost column that tells us the number to place in EAX.

The rightmost column tells us what parameters to push. They are pushed from right to left.

For example, to open a file, we need to push the mode first, then flags, then the address at which the path is stored.

This, and other documents, can be downloaded from ftp://ftp.FreeBSD.org/pub/FreeBSD/doc/.

For questions about FreeBSD, read the documentation before contacting <questions@FreeBSD.org>.
For questions about this documentation, e-mail <doc@FreeBSD.org>.




Партнёры:
PostgresPro
Inferno Solutions
Hosting by Hoster.ru
Хостинг:

Закладки на сайте
Проследить за страницей
Created 1996-2024 by Maxim Chirkov
Добавить, Поддержать, Вебмастеру