The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

fwcontrol (8)
  • >> fwcontrol (8) ( FreeBSD man: Команды системного администрирования )

  • BSD mandoc
     

    NAME

    
    
    fwcontrol
    
     - FireWire control utility
    
     
    

    SYNOPSIS

    [-u bus_num ] [-prt ] [-c node ] [-d node ] [-o node ] [-s node ] [-l file ] [-f node ] [-g gap_count ] [-b pri_req ] [-M mode ] [-R filename ] [-S filename ] [-m EUI64 | hostname ]  

    DESCRIPTION

    The utility is designed to provide a way for users to access and control the Fx FireWire subsystem. Without options, will output a list of devices that are/were connected to the bus.

    The following options are available:

    -u bus_num
    Specify the FireWire bus number to be operated on. The default is bus 0.
    -r
    Initiate bus reset.
    -t
    Show the topology map.
    -p
    Dump PHY registers.
    -c node
    Show the configuration ROM on the node.
    -d node
    Hex dump of the configuration ROM.
    -o node
    Send a link-on PHY packet to the node.
    -s node
    Write to the RESET_START register on the node.
    -l file
    Load hex dump file of the configuration ROM and parse it.
    -f node
    Force specified node to be the root node on the next bus reset by sending a PHY config packet. Valid values are 0 - 63.
    -g gap_count
    Broadcast new gap_count by sending a PHY_config packet. By default this value is 63 on all nodes. Valid values are 0 - 63.
    -i pri_req
    Set the PRIORITY_BUDGET register on all supported nodes.
    -M mode
    Explicitly specify either dv or mpeg mode for the incoming stream. Only meaningful in case of and must precede the -R option. If not specified, the program will try to guess. In case of ``format 0x20'' error, try to force the ``mpeg'' mode.
    -R filename
    Receive DV or MPEG TS stream and dump it to a file. Use ^C to stop the receiving. Some DV cameras seem not to send the stream if a bus manager exists. If it is impossible to get the stream, try the following commands:
    sysctl hw.firewire.try_bmr=0
    fwcontrol -r
    

    The resulting file contains raw DV data excluding isochronous header and CIP header. It can be handled by libdv in the Fx Ports Collection. Resulting MPEG TS stream can be played and sent over a network using the VideoLAN vlc tool in the Fx Ports Collection. The stream can be piped directly to vlc, see Sx EXAMPLES .

    -S filename
    Send a DV file as isochronous stream.
    -m EUI64 | hostname
    Set default fwmem target. Hostname will be converted to EUI64 using eui64(5).

     

    FILES

    /dev/fw0.0

     

    EXAMPLES

    Each DV frame has a fixed size and it is easy to edit the frame order.

    "fwcontrol -R original.dv"

    Receive a DV stream with DV camera attached.

    "dd if=original.dv of=first.dv bs=120000 count=30"

    Get first 30 frames(NTSC).

    "dd if=original.dv of=second.dv bs=120000 skip=30 count=30"

    Get second 30 frames(NTSC).

    "cat second.dv first.dv | fwcontrol -S /dev/stdin"

    Swap first and second 30 frames and send them to DV recorder.

    For PAL, replace ``bs=120000 '' with ``bs=144000 ''

    "fwcontrol -R file.m2t

    Receive an MPEG TS stream from a camera producing MPEG transport stream. This has been tested with SONY HDR-FX1E camera that produces HD MPEG-2 stream at 25 Mbps bandwidth.

    To send the stream from the camera over the network using TCP (which supprisingly works better with vlc), you can use

    "fwcontrol -R - | nc 192.168.10.11 9000
    with netcat from ports and to receive the stream, use
    nc -l -p 9000 | vlc

    To netcast via UDP, you need to use buffer program from ports, since vlc is not fast enough to read UDP packets from buffers and thus it experiences dropouts when run directly. The sending side can use

    "fwcontrol -R - | nc 192.168.10.11 9000
    and to receive the stream, use
    nc -l -u -p 9000 | buffer -s 10k -b 1000 -m 20m -p 5 | vlc

    For more information on how to work with vlc see its docs.  

    SEE ALSO

    mplayer(1), vlc(1), firewire(4), fwe(4), fwip(4), fwohci(4), sbp(4)  

    HISTORY

    The utility first appeared in Fx 5.0 .  

    AUTHORS

    An Hidetoshi Shimokawa Aq simokawa@FreeBSD.org An Petr Holub Aq hopet@ics.muni.cz - MPEG TS mode.  

    BUGS

    This utility is still under development and provided for debugging purposes. Especially MPEG TS reception support is very rudimental and supports only high-bandwidth MPEG-2 streams (fn field in CIP header equals 3).


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    FILES
    EXAMPLES
    SEE ALSO
    HISTORY
    AUTHORS
    BUGS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру