Никак не могу настроить общение Vlan'ов между Cisco'й 2960 и Роутером MikroTik Rb751. Мне нужно пробросить Vlan 1,3 на MiKrotik на разные порты. С цискки микротик пока не видно. Что пошло не так не понимаю.
#################Настройки Cisco.###############
[q]Switch#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
Fa0/25, Fa0/26, Fa0/27, Fa0/28
Fa0/29, Fa0/30, Fa0/31, Fa0/33
Fa0/34, Fa0/35, Fa0/41, Fa0/44
Fa0/45, Gi0/1, Gi0/2
2 VLAN0002 active Fa0/37, Fa0/38, Fa0/39, Fa0/40
3 VLAN0003 active
4 VLAN0004 active Fa0/48
[/q]
#####
Switch#configure t
Switch(config)#interface fastEthernet 0/43
Switch(config-if)#switchport mode trunk
Switch(config-if)#switchport trunk allowed vlan 1,3
Switch(config-if)#exit
#основаная сеть а дефолтном 1 вилане в который и хочу выпустить 1 порт микротика#
###################### Настройка MikroTik'a: ############################
#Созданы два Vlan#
[admin@MikroTik] > interface print
Flags: D - dynamic, X - disabled, R - running, S - slave
# NAME TYPE MTU L2MTU MAX-L2MTU
0 R ether1-gateway ether 1500 1600 4076
1 R ether2-master-local ether 1500 1598 2028
2 ether3-slave-local ether 1500 1598 2028
3 ether4-slave-local ether 1500 1598 2028
4 ether5-slave-local ether 1500 1598 2028
5 wlan1 wlan 1500 2290
6 R bridge-local bridge 1500 1598
7 R Pilot vlan 1500 1596
8 R Video vlan 1500 1596
9 R Pilot_br bridge 1500 1596
10 R video_br bridge 1500 1596
11 R eth5_pilot bridge 1500 65535
[admin@MikroTik] > interface vlan print
Flags: X - disabled, R - running, S - slave
# NAME MTU ARP VLAN-ID INTERFACE
0 R Pilot 1500 enabled 1 ether1-gateway
1 R Video 1500 enabled 3 ether1-gateway
#Обоим присвоены адреса адресация в Vlan правильная#
[admin@MikroTik] > ip address print
Flags: X - disabled, I - invalid, D - dynamic
# ADDRESS NETWORK INTERFACE
0 ;;; default configuration
192.168.88.1/24 192.168.88.0 wlan1
1 192.168.10.14/24 192.168.10.0 Pilot
2 192.168.1.14/24 192.168.1.0 Video
#Добавлены бриджи#
[admin@MikroTik] > interface bridge print
Flags: X - disabled, R - running
0 R name="bridge-local" mtu=1500 l2mtu=1598 arp=enabled
mac-address=D4:CA:6D:A6:03:97 protocol-mode=rstp priority=0x8000
auto-mac=no admin-mac=D4:CA:6D:A6:03:97 max-message-age=20s
forward-delay=15s transmit-hold-count=6 ageing-time=5m
1 R name="Pilot_br" mtu=1500 l2mtu=1596 arp=enabled
mac-address=D4:CA:6D:A6:03:96 protocol-mode=none priority=0x8000
auto-mac=yes admin-mac=00:00:00:00:00:00 max-message-age=20s
forward-delay=15s transmit-hold-count=6 ageing-time=5m
2 R name="video_br" mtu=1500 l2mtu=1596 arp=enabled
mac-address=D4:CA:6D:A6:03:96 protocol-mode=none priority=0x8000
auto-mac=yes admin-mac=00:00:00:00:00:00 max-message-age=20s
forward-delay=15s transmit-hold-count=6 ageing-time=5m
3 R name="eth5_pilot" mtu=1500 l2mtu=65535 arp=enabled
mac-address=00:00:00:00:00:00 protocol-mode=none priority=0x8000
auto-mac=yes admin-mac=00:00:00:00:00:00 max-message-age=20s
forward-delay=15s transmit-hold-count=6 ageing-time=5m
#Порты бриджей. Тут дополнительно пытаюсь прокинуть Vlan1(в циске он так зовётся) на 5 апорт микротика тут vlan зовётся Pilot#
[admin@MikroTik] > interface bridge port print
Flags: X - disabled, I - inactive, D - dynamic
# INTERFACE BRIDGE PRIORITY PATH-COST HORIZON
0 ether2-master-local bridge-local 0x80 10 none
1 I wlan1 bridge-local 0x80 10 none
2 ether1-gateway bridge-local 0x80 10 none
3 Pilot Pilot_br 0x80 10 none
4 Video video_br 0x80 10 none
5 I ether5-slave-local Pilot_br 0x80 10 nonе
