На Cisco2600Series не устанавливается дополнительная Ethernet к, Kovex, 27-Янв-10, 15:59 [смотреть все]Есть настроенная Cisco 2600 Series пытаюсь на нее установить дополнительный Ethernet порт, но после подключения в интерфейсах (просматриваю через команду sh int) этот порт отсутствует. Выдает Ethernet0/0 is up, line protocol is up Hardware is AmdP2, address is 0006.285b.ca40 (bia 0006.285b.ca40) Internet address is ххх.ххх.ххх.ххх/хх MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, reliability 255/255, txload 9/255, rxload 2/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 110000 bits/sec, 27 packets/sec 5 minute output rate 360000 bits/sec, 41 packets/sec 3812863 packets input, 2635153192 bytes, 0 no buffer Received 88478 broadcasts, 0 runts, 0 giants, 0 throttles 31446 input errors, 31434 CRC, 0 frame, 0 overrun, 12 ignored 0 input packets with dribble condition detected 3451879 packets output, 2123749766 bytes, 0 underruns(0/0/0) 0 output errors, 0 collisions, 2 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Serial0/0 is up, line protocol is up Hardware is PowerQUICC Serial Internet address is ххх.ххх.ххх.хх/хх MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 255/255, txload 16/255, rxload 59/255 Encapsulation HDLC, loopback not set Keepalive set (10 sec) Last input 00:00:07, output 00:00:00, output hang never Last clearing of "show interface" counters never Queueing strategy: fifo Output queue 0/40, 109532 drops; input queue 0/75, 0 drops 5 minute input rate 359000 bits/sec, 40 packets/sec 5 minute output rate 100000 bits/sec, 25 packets/sec 3454476 packets input, 2089607279 bytes, 0 no buffer Received 11344 broadcasts, 0 runts, 0 giants, 0 throttles 1 input errors, 0 CRC, 1 frame, 0 overrun, 0 ignored, 0 abort 3626638 packets output, 2484156006 bytes, 0 underruns 0 output errors, 0 collisions, 3 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=upSerial0/0.1 is up, line protocol is up Hardware is PowerQUICC Serial Internet address is ххх.ххх.ххх.хх/хх MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec, reliability 255/255, txload 16/255, rxload 59/255 Encapsulation HDLC Serial0/1 is administratively down, line protocol is down Hardware is PowerQUICC Serial MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation HDLC, loopback not set Keepalive set (10 sec) Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/0/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1158 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions DCD=down DSR=down DTR=down RTS=down CTS=down По всем читанным мануалом должен появится еще один интерфейс Ethernet0/1(или 1/0) после чего можено будет конфигурировать настройки данного интерфейса, однако результатов нет. Подскажите может после подключения надо дать команду на подключение или просто карта не рабочая (или порт куда подключаю), хотя снята данная карта с рабочей Cisco
|
- На Cisco2600Series не устанавливается дополнительная Etherne..., aZL, 16:52 , 27-Янв-10 (1)
укажите модель карты с Ethernet-портом и какой софт установлен на 2600
- На Cisco2600Series не устанавливается дополнительная Etherne..., Kovex, 06:23 , 28-Янв-10 (2)
>укажите модель карты с Ethernet-портом и какой софт установлен на 2600 Модель карты с Ethernet-портом Cisco XC4413-PQ208C Софт Building configuration... Current configuration : 2293 bytes ! version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime Вроде так!
- На Cisco2600Series не устанавливается дополнительная Etherne..., sh_, 11:44 , 28-Янв-10 (3)
- На Cisco2600Series не устанавливается дополнительная Etherne..., Kovex, 12:06 , 28-Янв-10 (4)
>Нет. >sh diag >sh ver Вот пожалста c2610.xxxxxxx#sh diag Slot 0: C2610 1E Mainboard Port adapter, 3 ports Port adapter is analyzed Port adapter insertion time unknown EEPROM contents at hardware discovery: Hardware Revision : 2.3 PCB Serial Number : JAD05180BTR (841737776) Part Number : 73-2839-13 RMA History : 00 RMA Number : 0-0-0-0 Board Revision : C0 Deviation Number : 0-0 EEPROM format version 4 EEPROM contents (hex): 0x00: 04 FF 40 00 91 41 02 03 C1 17 4A 41 44 30 35 31 0x10: 38 30 42 54 52 20 28 38 34 31 37 33 37 37 37 36 0x20: 29 82 49 0B 17 0D 04 00 81 00 00 00 00 42 43 30 0x30: 80 00 00 00 00 FF FF FF FF FF FF FF FF FF FF FF 0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF WIC Slot 0: Serial 2T (12in1) WAN daughter card Hardware revision 1.0 Board revision D0 Serial number 25727281 Part number 800-03181-01 Test history 0x0 RMA number 00-00-00 Connector type PCI EEPROM format version 1 EEPROM contents (hex): 0x20: 01 12 01 00 01 88 91 31 50 0C 6D 01 00 00 00 00 0x30: 68 00 00 00 01 07 20 00 FF FF FF FF FF FF FF FF c2610.xxxxxxx#sh ver Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-I-M), Version 12.1(5)T8, RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Mon 07-May-01 17:57 by ccai Image text-base: 0x80008088, data-base: 0x80972320
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1) ROM: C2600 Software (C2600-I-M), Version 12.1(5)T8, RELEASE SOFTWARE (fc1) c2610.heliosukg uptime is 6 hours, 3 minutes System returned to ROM by power-on System image file is "flash:c2600-i-mz.121-5.T8" cisco 2610 (MPC860) processor (revision 0x203) with 28672K/4096K bytes of memory . Processor board ID JAD05180BTR (841737776) M860 processor: part number 0, mask 49 Bridging software. X.25 software, Version 3.0.0. 1 Ethernet/IEEE 802.3 interface(s) 2 Serial(sync/async) network interface(s) 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read/Write) Configuration register is 0x2102
|