slackware 11.0, после перехода на ядро 2.6 не опознаются флешки, устройства sdx не создаются, модули все загружены, hotplug - исполняемый, etc
логи:

dmesg.log
errupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:01.0
  IO window: d000-dfff
  MEM window: e8000000-e80fffff
  PREFETCH window: d0000000-dfffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.27 [Flags: R/W].
JFS: nTxBlock = 6021, nTxLock = 48175
SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 2.6.10)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: VIA IRQ fixup for 0000:00:0f.0, from 255 to 11
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.0
    ide0: BM-DMA at 0xe200-0xe207, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xe208-0xe20f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: ST340014A, ATA DISK drive
hdb: ST380011A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: LITE-ON LTR-52327S, ATAPI CD/DVD-ROM drive
hdd: LITE-ON DVDRW SHW-16H5S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 > hda3 hda4
hdb: max request size: 512KiB
hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hdb: cache flushes supported
hdb: hdb1
hdc: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
ide-floppy driver 0.99.newide
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
Adaptec aacraid driver (1.1-5[2409]-mh1)
scsi: <fdomain> Detection failed (no card)
sym53c416.c: Version 1.0.0-ac
qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver
Emulex LightPulse Fibre Channel SCSI driver 8.1.6
Copyright(c) 2004-2006 Emulex.  All rights reserved.
Failed initialization of WD-7000 SCSI card!
megaraid cmm: 2.20.2.6 (Release Date: Mon Mar 7 00:01:03 EST 2005)
megaraid: 2.20.4.8 (Release Date: Mon Apr 11 12:27:22 EST 2006)
megasas: 00.00.02.04 Fri Feb 03 14:31:44 PST 2006
GDT-HA: Storage RAID Controller Driver. Version: 3.04
GDT-HA: Found 0 PCI Storage RAID Controllers
3ware Storage Controller device driver for Linux v1.26.02.001.
3ware 9000 Storage Controller device driver for Linux v2.26.02.007.
nsp32: loading...
ipr: IBM Power RAID SCSI Device Driver version: 2.1.3 (March 29, 2006)
libata version 1.20 loaded.
st: Version 20050830, fixed bufsize 32768, s/g segs 256
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
I2O Bus Adapter OSM v1.317
I2O Block Device OSM v1.325
I2O SCSI Peripheral OSM v1.316
I2O ProcFS OSM v1.316
Fusion MPT base driver 3.03.09
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SPI Host driver 3.03.09
Fusion MPT FC Host driver 3.03.09
Fusion MPT SAS Host driver 3.03.09
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:0a.2 -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11]  MMIO=[e8104000-e81047ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
usbmon: debugfs is not available
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
irq 10: nobody cared (try booting with the "irqpoll" option)
<c0133982> __report_bad_irq+0x22/0x90  <c0133a98> note_interrupt+0x78/0xc0
<c01334a9> __do_IRQ+0x99/0xb0  <c01048da> do_IRQ+0x1a/0x30
<c010305a> common_interrupt+0x1a/0x20  <c011d250> __do_softirq+0x30/0xb0
<c011d305> do_softirq+0x35/0x40  <c01048df> do_IRQ+0x1f/0x30
<c010305a> common_interrupt+0x1a/0x20  <c0133684> setup_irq+0x94/0x100
<c04dab50> usb_hcd_irq+0x0/0x60  <c0133844> request_irq+0x74/0xa0
<c04dae61> usb_add_hcd+0x181/0x350  <c04dab50> usb_hcd_irq+0x0/0x60
<c04e291c> usb_hcd_pci_probe+0x17c/0x350  <c02f2551> pci_call_probe+0x11/0x20
<c02f25aa> __pci_device_probe+0x4a/0x60  <c02f25df> pci_device_probe+0x1f/0x40
<c03477d3> driver_probe_device+0x53/0xa0  <c03478a0> __driver_attach+0x0/0x70
<c034790b> __driver_attach+0x6b/0x70  <c0346d78> bus_for_each_dev+0x58/0x80
<c02e603c> kobject_add+0x5c/0xd0  <c0347925> driver_attach+0x15/0x20
<c03478a0> __driver_attach+0x0/0x70  <c0347259> bus_add_driver+0x69/0xa0
<c0347d9a> driver_register+0x5a/0x90  <c04c1af9> nodemgr_create_drv_files+0x19/0x30
<c02f284e> __pci_register_driver+0x3e/0x60  <c0118e6f> printk+0xf/0x20
<c077a46a> ehci_hcd_pci_init+0x1a/0x30  <c07547d9> do_initcalls+0x79/0x120
<c0133e1d> register_irq_proc+0x6d/0x80  <c01002b0> init+0x0/0x1a0
<c01002dd> init+0x2d/0x1a0  <c0101355> kernel_thread_helper+0x5/0x10
handlers:
[<c04dab50>] (usb_hcd_irq+0x0/0x60)
Disabling IRQ #10
ehci_hcd 0000:00:10.4: irq 10, io mem 0xe8105000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 11, io base 0x0000e300
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 11, io base 0x0000e400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:10.2 -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: VIA IRQ fixup for 0000:00:10.2, from 5 to 10
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 10, io base 0x0000e500
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3 -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: VIA IRQ fixup for 0000:00:10.3, from 5 to 10
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 10, io base 0x0000e600
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023c010107472c]
sl811: driver sl811-hcd, 19 May 2005
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: automatically using best checksumming function: pIII_sse
   pIII_sse  :  3093.000 MB/sec
raid5: using function: pIII_sse (3093.000 MB/sec)
raid6: int32x1    748 MB/s
raid6: int32x2    958 MB/s
raid6: int32x4    567 MB/s
raid6: int32x8    524 MB/s
raid6: mmxx1     1511 MB/s
raid6: mmxx2     2665 MB/s
raid6: sse1x1    1420 MB/s
raid6: sse1x2    2400 MB/s
raid6: using algorithm sse1x2 (2400 MB/s)
md: raid6 personality registered for level 6
md: multipath personality registered for level -4
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
SLPB PCI0 USB0 USB1 USB2 USB6 USB7 USB8 USB9 LAN0 UAR1 LPT1
ACPI: (supports S0 S1 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
ReiserFS: hda4: found reiserfs format "3.6" with standard journal
input: AT Translated Set 2 keyboard as /class/input/input0
ReiserFS: hda4: using ordered data mode
ReiserFS: hda4: journal params: device hda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda4: checking transaction log (hda4)
ReiserFS: hda4: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 284k freed
Adding 747012k swap on /dev/hda3.  Priority:-1 extents:1 across:747012k
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
Installing spdif_bug patch: Audigy 2 [SB0240]
i2c_core: exports duplicate symbol i2c_register_driver (owned by kernel)
ieee1394: exports duplicate symbol hpsb_alloc_host (owned by kernel)
ohci1394: exports duplicate symbol ohci1394_stop_context (owned by kernel)
gameport: EMU10K1 is pci0000:00:0a.1/gameport0, io 0xe100, speed 1242kHz
PCI: Enabling device 0000:00:11.5 (0000 -> 0001)
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.5 to 64
Linux agpgart interface v0.101 (c) Dave Jones
USB Universal Host Controller Interface driver v3.0
kmem_cache_create: duplicate cache uhci_urb_priv
<c014dd1f> kmem_cache_create+0x30f/0x3b0  <f0e05033> uhci_hcd_init+0x33/0x92 [uhci_hcd]
<c0130e52> sys_init_module+0xe2/0x160  <c0102de7> syscall_call+0x7/0xb
USB Universal Host Controller Interface driver v3.0
kmem_cache_create: duplicate cache uhci_urb_priv
<c014dd1f> kmem_cache_create+0x30f/0x3b0  <f0e05033> uhci_hcd_init+0x33/0x92 [uhci_hcd]
<c0130e52> sys_init_module+0xe2/0x160  <c0102de7> syscall_call+0x7/0xb
USB Universal Host Controller Interface driver v3.0
kmem_cache_create: duplicate cache uhci_urb_priv
<c014dd1f> kmem_cache_create+0x30f/0x3b0  <f0e05033> uhci_hcd_init+0x33/0x92 [uhci_hcd]
<c0130e52> sys_init_module+0xe2/0x160  <c0102de7> syscall_call+0x7/0xb
USB Universal Host Controller Interface driver v3.0
kmem_cache_create: duplicate cache uhci_urb_priv
<c014dd1f> kmem_cache_create+0x30f/0x3b0  <f0e05033> uhci_hcd_init+0x33/0x92 [uhci_hcd]
<c0130e52> sys_init_module+0xe2/0x160  <c0102de7> syscall_call+0x7/0xb
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 128M @ 0xe0000000
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input1
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
lp0: using parport0 (polling).
lp0: console ready
Capability LSM initialized
ieee1394: exports duplicate symbol hpsb_alloc_host (owned by kernel)
ohci1394: exports duplicate symbol ohci1394_stop_context (owned by kernel)
USB Universal Host Controller Interface driver v3.0
kmem_cache_create: duplicate cache uhci_urb_priv
<c014dd1f> kmem_cache_create+0x30f/0x3b0  <f0e05033> uhci_hcd_init+0x33/0x92 [uhci_hcd]
<c0130e52> sys_init_module+0xe2/0x160  <c0102de7> syscall_call+0x7/0xb
USB Universal Host Controller Interface driver v3.0
kmem_cache_create: duplicate cache uhci_urb_priv
<c014dd1f> kmem_cache_create+0x30f/0x3b0  <f0e05033> uhci_hcd_init+0x33/0x92 [uhci_hcd]
<c0130e52> sys_init_module+0xe2/0x160  <c0102de7> syscall_call+0x7/0xb
USB Universal Host Controller Interface driver v3.0
kmem_cache_create: duplicate cache uhci_urb_priv
<c014dd1f> kmem_cache_create+0x30f/0x3b0  <f0e05033> uhci_hcd_init+0x33/0x92 [uhci_hcd]
<c0130e52> sys_init_module+0xe2/0x160  <c0102de7> syscall_call+0x7/0xb
USB Universal Host Controller Interface driver v3.0
kmem_cache_create: duplicate cache uhci_urb_priv
<c014dd1f> kmem_cache_create+0x30f/0x3b0  <f0e05033> uhci_hcd_init+0x33/0x92 [uhci_hcd]
<c0130e52> sys_init_module+0xe2/0x160  <c0102de7> syscall_call+0x7/0xb
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
usb 1-8: new high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:10.4: Unlink after no-IRQ?  Controller is probably using the wrong IRQ.
usb 1-8: device not accepting address 2, error -110
usb 1-8: new high speed USB device using ehci_hcd and address 3
usb 1-8: device not accepting address 3, error -110
usb 1-8: new high speed USB device using ehci_hcd and address 4
usb 1-8: device not accepting address 4, error -110
usb 1-8: new high speed USB device using ehci_hcd and address 5
usb 1-8: device not accepting address 5, error -110

lsmod.log
Module                  Size  Used by
snd_seq_dummy           2820  0
snd_seq_oss            28928  0
snd_seq_midi_event      5888  1 snd_seq_oss
snd_seq                43984  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_pcm_oss            38048  0
snd_mixer_oss          15616  1 snd_pcm_oss
ipv6                  223584  10
sg                     26524  0
capability              3336  0
commoncap               5376  1 capability
lp                      9800  0
parport_pc             24132  1
parport                30024  2 lp,parport_pc
pcspkr                  2432  0
psmouse                34952  0
shpchp                 33816  0
evdev                   8064  0
via_agp                 7808  1
serio_raw               5252  0
agpgart                28080  1 via_agp
snd_via82xx            22808  0
emu10k1_gp              2944  0
gameport               10760  3 snd_via82xx,emu10k1_gp
i2c_viapro              7572  0
snd_mpu401_uart         6016  1 snd_via82xx
snd_emu10k1           104356  0
snd_rawmidi            18720  2 snd_mpu401_uart,snd_emu10k1
snd_ac97_codec         86304  2 snd_via82xx,snd_emu10k1
snd_ac97_bus            2048  1 snd_ac97_codec
snd_pcm                73736  4 snd_pcm_oss,snd_via82xx,snd_emu10k1,snd_ac97_codec
snd_seq_device          6284  5 snd_seq_dummy,snd_seq_oss,snd_seq,snd_emu10k1,snd_rawmidi
snd_timer              19332  3 snd_seq,snd_emu10k1,snd_pcm
snd_page_alloc          7560  3 snd_via82xx,snd_emu10k1,snd_pcm
snd_util_mem            3328  1 snd_emu10k1
snd_hwdep               6660  1 snd_emu10k1
snd                    43364  13 snd_seq_oss,snd_seq,snd_pcm_oss,snd_mixer_oss,snd_via82xx,snd_mpu401_uart,snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_pcm,snd_seq_device,snd_timer,snd_hwdep
soundcore               7136  1 snd

lsusb.log
Bus 5 Device 1: ID 0000:0000  
Bus 2 Device 1: ID 0000:0000  
Bus 5 Device 1: ID 0000:0000  
Bus 3 Device 1: ID 0000:0000  
Bus 1 Device 1: ID 0000:0000