- Телефонный шлюз на CISCO3640,
 mdenisov, 09:05 , 08-Сен-13 (1)
- Телефонный шлюз на CISCO3640, Konstantin_PL, 11:02 , 09-Сен-13 (2)
> Скорее всего у вас путаница с dial-peer'ами - станция шлет вызов циске,
> она шлет его астериску и вторым выбором опять на станцию и
> так получается кольцо. Скажите с какого номера и на какой такое
> происходит, покажите sh run | sec dial-peer, а также debug isdn
> q931 для одного такого проблемного вызова.День добрый!
Вот что получилось: Звонил с 3517780512 и 3517780515 на номер 92287 GW-3640#sh run | sec dial-peer
dial-peer voice 1 voip
description IN from IP net
huntstop
answer-address .T
voice-class codec 1
dial-peer voice 2 pots
description IN from E1 net
preference 1
incoming called-number [5,9][5,2].T
no digit-strip
direct-inward-dial
forward-digits all
dial-peer voice 1001 voip
description OUT from E1 to IP
destination-pattern 9228[123456789]$
voice-class codec 1
session protocol sipv2
session target ipv4:192.168.100.1
dtmf-relay rtp-nte
no vad
dial-peer voice 1002 pots
description OUT from IP to E1
destination-pattern 0.$
port 2/0:15
forward-digits all
dial-peer voice 1003 pots
description OUT from IP to E1
destination-pattern 8..........
port 2/0:15
forward-digits all
dial-peer voice 1004 pots
description OUT from IP to E1
destination-pattern 810...............
port 2/0:15
forward-digits all
dial-peer voice 1005 pots
description OUT from IP to E1
destination-pattern [2479]....$
port 2/0:15
forward-digits all
dial-peer voice 1006 pots
description OUT from IP to E1
destination-pattern 118..$
port 2/0:15
forward-digits all
dial-peer voice 1000 voip
description FOR 92186
destination-pattern 5592186$
translate-outgoing called 55
voice-class codec 1
session protocol sipv2
session target ipv4:192.168.100.1
dtmf-relay rtp-nte
no vad
dial-peer voice 999 voip
description OUT from E1 to IP
destination-pattern 9272[0123]$
voice-class codec 1
session protocol sipv2
session target ipv4:192.168.100.1
dtmf-relay rtp-nte
no vad
dial-peer voice 998 voip
description FOR 92719
destination-pattern 5592719$
translate-outgoing called 55
voice-class codec 1
session protocol sipv2
session target ipv4:192.168.100.1
dtmf-relay rtp-nte
no vad
dial-peer voice 997 voip
description FOR 92800 SUPPORT Teh
destination-pattern 5592800$
translate-outgoing called 55
voice-class codec 1
session protocol sipv2
session target ipv4:192.168.100.1
dtmf-relay rtp-nte
no vad
GW-3640# ========
GW-3640#terminal monitor
GW-3640#
GW-3640#
GW-3640#
GW-3640#
GW-3640#debug isdn q931
debug isdn q931 is ON.
GW-3640#
GW-3640#
GW-3640#
000062: Sep 9 12:40:40: ISDN Se2/0:15 Q931: RX <- SETUP pd = 8 callref = 0x016A
Sending Complete
Bearer Capability i = 0x9090A3
Standard = CCITT
Transfer Capability = 3.1kHz Audio
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98382
Exclusive, Channel 2
Progress Ind i = 0x8283 - Origination address is non-ISDN
Calling Party Number i = 0x0080, '3517780515'
Plan:Unknown, Type:Unknown
Called Party Number i = 0xA1, '92287'
Plan:ISDN, Type:National
000063: Sep 9 12:40:40: ISDN Se2/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x816A
Channel ID i = 0xA98382
Exclusive, Channel 2
000064: Sep 9 12:40:40: ISDN Se2/0:15 Q931: TX -> ALERTING pd = 8 callref = 0x816A
000065: Sep 9 12:40:44: ISDN Se2/0:15 Q931: RX <- SETUP pd = 8 callref = 0x016B
Sending Complete
Bearer Capability i = 0x9090A3
Standard = CCITT
Transfer Capability = 3.1kHz Audio
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98383
Exclusive, Channel 3
Progress Ind i = 0x8283 - Origination address is non-ISDN
Calling Party Number i = 0x0080, '3517780512'
Plan:Unknown, Type:Unknown
Called Party Number i = 0xA1, '92287'
Plan:ISDN, Type:National
000066: Sep 9 12:40:44: ISDN Se2/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x816B
Channel ID i = 0xA98383
Exclusive, Channel 3
000067: Sep 9 12:40:44: ISDN Se2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Calling num 3517780512
000068: Sep 9 12:40:44: ISDN Se2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x2 0x1, Called num 92287
000069: Sep 9 12:40:44: ISDN Se2/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0097
Sending Complete
Bearer Capability i = 0x9090A3
Standard = CCITT
Transfer Capability = 3.1kHz Audio
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839F
Exclusive, Channel 31
Progress Ind i = 0x8283 - Origination address is non-ISDN
Calling Party Number i = 0x0080, '3517780512'
Plan:Unknown, Type:Unknown
Called Party Number i = 0xA1, '92287'
Plan:ISDN, Type:National
000070: Sep 9 12:40:45: ISDN Se2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Calling num 3517780512
000071: Sep 9 12:40:45: ISDN Se2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x2 0x1, Called num 92287
000072: Sep 9 12:40:45: ISDN Se2/0:15 Q931: TX -> SETUP pd = 8 callref = 0x009A
Sending Complete
Bearer Capability i = 0x9090A3
Standard = CCITT
Transfer Capability = 3.1kHz Audio
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839C
Exclusive, Channel 28
Progress Ind i = 0x8283 - Origination address is non-ISDN
Calling Party Number i = 0x0080, '3517780512'
Plan:Unknown, Type:Unknown
Called Party Number i = 0xA1, '92287'
Plan:ISDN, Type:National
000073: Sep 9 12:40:45: ISDN Se2/0:15 Q931: RX <- SETUP pd = 8 callref = 0x016F
Sending Complete
Bearer Capability i = 0x9090A3
Standard = CCITT
Transfer Capability = 3.1kHz Audio
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98387
Exclusive, Channel 7
Progress Ind i = 0x8283 - Origination address is non-ISDN
Calling Party Number i = 0x0080, '3517780512'
Plan:Unknown, Type:Unknown
Called Party Number i = 0xA1, '92287'
Plan:ISDN, Type:National
000074: Sep 9 12:40:45: ISDN Se2/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x816F
Channel ID i = 0xA98387
Exclusive, Channel 7
000075: Sep 9 12:40:46: ISDN Se2/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x809D
Channel ID i = 0xA98399
Exclusive, Channel 25
000076: Sep 9 12:40:46: ISDN Se2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Calling num 3517780512
000077: Sep 9 12:40:46: ISDN Se2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x2 0x1, Called num 92287
000078: Sep 9 12:40:46: ISDN Se2/0:15 Q931: TX -> SETUP pd = 8 callref = 0x009E
Sending Complete
Bearer Capability i = 0x9090A3
Standard = CCITT
Transfer Capability = 3.1kHz Audio
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98398
Exclusive, Channel 24
Progress Ind i = 0x8283 - Origination address is non-ISDN
Calling Party Number i = 0x0080, '3517780512'
Plan:Unknown, Type:Unknown
Called Party Number i = 0xA1, '92287'
Plan:ISDN, Type:National
000079: Sep 9 12:40:46: ISDN Se2/0:15 Q931: RX <- SETUP pd = 8 callref = 0x0173
Sending Complete
Bearer Capability i = 0x9090A3
Standard = CCITT
Transfer Capability = 3.1kHz Audio
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9838B
Exclusive, Channel 11
Progress Ind i = 0x8283 - Origination address is non-ISDN
Calling Party Number i = 0x0080, '3517780512'
Plan:Unknown, Type:Unknown
Called Party Number i = 0xA1, '92287'
Plan:ISDN, Type:National
000080: Sep 9 12:40:47: ISDN Se2/0:15 Q931: RX <- SETUP pd = 8 callref = 0x0176
Sending Complete
Bearer Capability i = 0x9090A3
Standard = CCITT
Transfer Capability = 3.1kHz Audio
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9838E
Exclusive, Channel 14
Progress Ind i = 0x8283 - Origination address is non-ISDN
Calling Party Number i = 0x0080, '3517780512'
Plan:Unknown, Type:Unknown
Called Party Number i = 0xA1, '92287'
Plan:ISDN, Type:National
000081: Sep 9 12:40:47: ISDN Se2/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x8176
Channel ID i = 0xA9838E
Exclusive, Channel 14
000082: Sep 9 12:40:47: ISDN Se2/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x80A1
Channel ID i = 0xA98395
Exclusive, Channel 21
000083: Sep 9 12:40:47: ISDN Se2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Calling num 3517780512
000084: Sep 9 12:40:47: ISDN Se2/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x2 0x1, Called num 92287
000085: Sep 9 12:40:47: ISDN Se2/0:15 Q931: TX -> SETUP pd = 8 callref = 0x00A2
Sending Complete
Bearer Capability i = 0x9090A3
Standard = CCITT
Transfer Capability = 3.1kHz Audio
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98394
Exclusive, Channel 20
Progress Ind i = 0x8283
000086: Sep 9 12:40:48: ISDN Se2/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x0177
000087: Sep 9 12:40:48: ISDN Se2/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x8177
000088: Sep 9 12:40:48: ISDN Se2/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x80A2
Cause i = 0x80A2 - No circuit/channel available
000089: Sep 9 12:40:48: ISDN Se2/0:15 Q931: TX -> RELEASE pd = 8 callref = 0x00A2
000090: Sep 9 12:40:48: ISDN Se2/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x80A2
000091: Sep 9 12:40:49: ISDN Se2/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x0170
000092: Sep 9 12:40:49: ISDN Se2/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x8170
000093: Sep 9 12:40:49: ISDN Se2/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x809B
Cause i = 0x80A2 - No circuit/channel available
000094: Sep 9 12:40:49: ISDN Se2/0:15 Q931: TX -> RELEASE pd = 8 callref = 0x009B
000095: Sep 9 12:40:49: ISDN Se2/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x809B
000096: Sep 9 12:40:58: ISDN Se2/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x016A
Cause i = 0x8490 - Normal call clearing
000097: Sep 9 12:40:58: ISDN Se2/0:15 Q931: TX -> RELEASE pd = 8 callref = 0x816A
000098: Sep 9 12:40:58: ISDN Se2/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x016A
GW-3640#
GW-3640#no debug all
All possible debugging has been turned off
GW-3640#
- Телефонный шлюз на CISCO3640, mdenisov, 15:42 , 09-Сен-13 (3)
- Телефонный шлюз на CISCO3640, Konstantin_PL, 16:37 , 09-Сен-13 (4)
>[оверквотинг удален]
> номер, затем anwser address - вызывающий номер, затем destination-pattern - вызываемый
> или вызывающий номер. Для pots пиров также учитывается port или trunk
> gorup в качестве фильтра. Если условию удовлетворяют несколько пиров, выбирается пир
> с большим preference. При прочих равных выбирается pots пир.
> Для простоты понимания рекомендую разбивать входящие и исходящие пиры и везде явно
> прописывать permission. Также регулярные выражения лучше прописывать не допуская вариаций,
> например ^10[13-5].$
> Разбираться в ваших пирах мне лениво, анализируйте show dialplan number, смотрите sh
> call hist voice br, там pid это номер пира, или разбирайте
> debug voip dial-peer.Спасибо!
Буду в очередной раз читать доки... Константин.
|
Версия для распечатки
Телефонный шлюз на CISCO3640, 
