Всем доброго дня! Очень нуждаюсь в помощи. Приобрел Cisco 1841 и стоит цель настроите ее так что бы Юзвери могли ходить в интернет. Интерфейса два. вот мой конфиг
cisco#sh run
Building configuration...Current configuration : 2171 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname cisco
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
enable secret 5 *******************
enable password ******************
!
username cisco privilege 15 secret 5 **************
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
no aaa new-model
ip subnet-zero
no ip source-route
no ip routing
no ip cef
!
!
!
!
ip domain name yourdomain.com
ip ips po max-events 100
no ip rcmd domain-lookup
no ftp-server write-enable
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface FastEthernet0/0
description ip:office
ip address 192.168.20.179 255.255.255.0
ip nat inside
ip virtual-reassembly
no ip route-cache
speed auto
half-duplex
no cdp enable
no mop enabled
!
interface FastEthernet0/1
ip address 213.247.189.202 255.255.255.248
ip nat outside
ip virtual-reassembly
ip route-cache policy
ip policy route-map MAP
duplex auto
speed auto
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 213.247.189.201
!
ip http server
ip http authentication local
ip http secure-server
!
!
no cdp run
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
banner login ^C
-----------------------------------------------------------------------
Cisco Router and Security Device Manager (SDM) is installed on this device. This
feature requires the one time use, initial credentials, of username "cisco"
with password "cisco".
Please change these publicly known initial credentials through SDM or IOS CLI.
Here's the Cisco IOS command:
no username cisco
NOTE: Please add a new username to be able to launch SDM for router management.
For more information about SDM please follow the instructions in the QUICK
START GUIDE for your router or at
http://www.cisco.com/go/sdm
-----------------------------------------------------------------------
^C
!
line con 0
login local
line aux 0
line vty 0 4
privilege level 15
password gfnhjyxbr
login local
transport input telnet ssh
line vty 5 15
privilege level 15
password gfnhjyxbr
login local
transport input telnet ssh
!
end
Проблема вот в чем пингуется провайдер его шлюз но не ходит она сама в сеть. То есть я пингую страничку или хост какой нить она ругается ...или же даю команду telnet www.ru 80 тоже не хочет.
isco#ping 213.247.189.202
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 213.247.189.202, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
cisco#ping 213.247.189.201
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 213.247.189.201, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/201/1000 ms
cisco#ping 194.186.193.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 194.186.193.1, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
cisco#ping 194.186.193.10
Прошу вас помочь мне ... только не хотелось бы получать ответы от умников типа иди туда почитай вот это....... Заранее благодарен
