>[оверквотинг удален]
>>
>>Как быть помоги плизззз.....
>>
>>Заранее спасибо;)
>
>SMPPPD_BIN= /work/sms/sms.sh
>
>а так:
>
>ps ax | grep sms.sh Попробуй этот скрипт:
=============================================================
#! /bin/sh
## BEGIN INIT INFO
# Provides: sms
# Required-Start: $remote_fs $network $syslog
# Should-Start: isdn $named slpd
# Required-Stop: $remote_fs $network $syslog
# Should-Stop: isdn $named slpd
# Default-Start: 2 3 5
# Default-Stop: 0 1 6
# Description: Start the sms.
### END INIT INFO
# Set some defaults
SMPPPD="sms.sh"
SMPPPD_BIN_DIR=/work/sms
SMPPPD_PID_FILE=/var/run/sms.pid
SMPPPD_PID=/var/run/sms.pid
SMPPPD_BIN=$SMPPPD_BIN_DIR/$SMPPPD
#PID=`ps -aef | grep "$SMPPPD" | grep -v grep | awk '{print $2}'`
# Source LSB init functions
# providing start_daemon, killproc, pidofproc,
# log_success_msg, log_failure_msg and log_warning_msg.
# This is currently not used by UnitedLinux based distributions and
# not needed for init scripts for UnitedLinux only. If it is used,
# the functions from rc.status should not be sourced or used.
#. /lib/lsb/init-functions
test -x $SMPPPD_BIN || { echo "$SMPPPD_BIN not installed";
if [ "$1" = "stop" ]; then exit 0;
else exit 5; fi; }
# Shell functions sourced from /etc/rc.status:
# rc_check check and set local and overall rc status
# rc_status check and set local and overall rc status
# rc_status -v be verbose in local rc status and clear it afterwards
# rc_status -v -r ditto and clear both the local and overall rc status
# rc_status -s display "skipped" and exit with status 3
# rc_status -u display "unused" and exit with status 3
# rc_failed set local and overall rc status to failed
# rc_failed <num> set local and overall rc status to <num>
# rc_reset clear both the local and overall rc status
# rc_exit exit appropriate to overall rc status
# rc_active checks whether a service is activated by symlinks
# rc_splash arg sets the boot splash screen to arg (if active)
. /etc/rc.status
# Reset status of this service
rc_reset
# Return values acc. to LSB for all commands but status:
# 0 - success
# 1 - generic or unspecified error
# 2 - invalid or excess argument(s)
# 3 - unimplemented feature (e.g. "reload")
# 4 - user had insufficient privileges
# 5 - program is not installed
# 6 - program is not configured
# 7 - program is not running
# 8--199 - reserved (8--99 LSB, 100--149 distrib, 150--199 appl)
#
# Note that starting an already running service, stopping
# or restarting a not-running service as well as the restart
# with force-reload (in case signaling is not supported) are
# considered a success.
case "$1" in
start)
echo -n "Starting SMPPPD"
startproc $SMPPPD_BIN
rc_status -v
;;
stop)
echo -n "Shutting down SMPPPD"
killproc $SMPPPD_BIN
rc_status -v
;;
try-restart)
$0 status >/dev/null && $0 restart
rc_status
;;
restart)
$0 stop
$0 start
rc_status
;;
status)
echo -n "Checking for SMPPPD: "
## Check status with checkproc(8), if process is running
## checkproc will return with exit status 0.
# Status has a slightly different for the status command:
# 0 - service running
# 1 - service dead, but /var/run/ pid file exists
# 2 - service dead, but /var/lock/ lock file exists
# 3 - service not running
# NOTE: checkproc returns LSB compliant status values.
checkproc $SMPPPD_BIN
rc_status -v
;;
force-reload)
## Signal the daemon to reload its config. Most daemons
## do this on signal 1 (SIGHUP).
## If it does not support it, restart.
echo -n "Reload service SMPPPD"
echo ""
$0 stop && $0 start
rc_status
;;
probe)
test $SMPPPD_PID_FILE && \
echo restart
;;
*)
echo "Usage: $0 {start|stop|status|try-restart|restart|force-reload|reload}"
;;
esac
rc_exit
====================================================================================
