Доброго времени суток!
Народ, может кто подскажет, что это upsd у меня бузит, ежеминутно выдавая следующую диагностику:
Jan 8 22:33:54 aliot upsd[51607]: apc_tune: toggle wraparound register high-transfer-point
Jan 8 22:33:55 aliot upsd[51607]: apc_tune: toggle wraparound register line-alarm
Jan 8 22:33:55 aliot upsd[51607]: apc_tune: toggle wraparound register line-sensitivity
Jan 8 22:33:55 aliot upsd[51607]: apc_tune: negative response: NO
Jan 8 22:33:55 aliot upsd[51607]: apc_tune: toggle wraparound register wakeup-batteries-capacity
Jan 8 22:33:58 aliot upsd[51607]: last test: NO, light test:
Jan 8 22:33:58 aliot upsd[51607]: frequency: 50.00, maxvac: 218.8, minvac: 214.5, voltage: 217.4
Jan 8 22:33:58 aliot upsd[51607]: load: 49.4, recharge: 100.0, temp: 0.0, vdc: 13.85, output voltage: 217.4
вот его upsd.conf:
$ cat /etc/upsd.conf
# $FreeBSD: ports/sysutils/upsd/files/upsd.conf,v 1.2 1999/08/31 02:00:16 peter Exp $
#
# UPS Daemon
# The Wild Wind Communications, 1995, 1996
# Modification (c) 2003 by proff (Aliot SWLab, Moscow)
# $Id: upsd.conf,v 1.6 2003/01/06 11:49:14 proff Exp $
#
ups "smart-ups" (230) proto "apc-smart" {
device "/dev/cuaa0" # COM1
speed 2400
read-timeout 2
write-block-size 1
write-block-delay 50
queue-size 64
}
every 5 { # check events every 5 seconds
nop
}
on "initialize" != "SM" {
poll "initialize"
after 60 every 60 {
log emerg "Cannot put the UPS into smart mode!"
}
}
#on "initialize" {
# log notice "Initialize event handled"
#}
every 86400 {
tune "high-transfer-point" 264
tune "low-transfer-point" 196
tune "line-alarm" "0"
tune "line-sensitivity" "L"
tune "low-batteries-duration" 2
tune "nominal-voltage" 220
tune "shutdown-delay" 20
tune "wakeup-batteries-capacity" 25
tune "wakeup-delay" 0
# tune "batteries-replaced" "01/01/77"
# tune "label" "WildWind"
}
every 3600 { # poll the UPS
poll "last-test"
# poll "light-test"
poll "line-frequency"
poll "line-maxvac"
poll "line-minvac"
poll "line-voltage"
poll "load"
poll "recharge"
poll "temperature"
poll "vdc"
poll "voltage"
#log notice "last test: %last-test%, light test: %light-test%"
#log notice "frequency: %line-frequency%, maxvac: %line-maxvac%, minvac: %line-minvac%, voltage: %line-voltage%"
#log notice "load: %load%, recharge: %recharge%, temp: %temperature%, vdc: %vdc%, output voltage: %voltage%"
log notice "load: %load%, recharge: %recharge%, temp: %temperature%, vdc: %vdc%, in-voltage: %line-voltage%, out-voltage: %voltage%"
on "load" > 95 {
log alert "WARNING! UPS load is too high: %load%"
}
}
on "line-fail" {
log emerg "ALERT! Source power line failed, save your work!"
}
on "line-fail" after 60 {
log emerg "ALERT! System shutdown in 120 seconds, save your work!"
}
on "line-fail" after 120 {
log emerg "ALERT! System shutdown in 60 seconds, LOGOUT NOW!"
}
on "line-fail" after 150 {
log emerg "ALERT! System shutdown in 30 seconds, LOGOUT NOW!"
}
on "line-fail" after 170 {
log emerg "ALERT! System shutdown in 10 seconds, LOGOUT NOW!"
}
on "line-restore" {
log emerg "Source power line restored, you may continue your work."
}
on "line-fail" after 180 {
log emerg "ALERT! THE SYSTEM IS SHUTTING DOWN!"
poll "shutdown"
poll "shutdown"
poll "power-test"
poll "power-test"
poll "shutdown"
poll "shutdown"
sleep 2
exec "/sbin/halt &"
poll "power-test"
poll "shutdown"
poll "power-test"
poll "shutdown"
poll "power-test"
poll "shutdown"
poll "power-test"
sleep 1000 # let us wait peacefully
}
кабель от UPSa -- тот, что был в коробке...
p.s. с прошедшими и наступающими (СНГ) праздниками!
Вариант для распечатки
OpenNET: Виртуальная конференция (Public)
on
08-Янв-03, 22:44 (MSK)
