Проект OpenNet: MAN geom_fox (4) Специальные файлы /dev/* (FreeBSD и Linux)

Интерактивная система просмотра системных руководств (man-ов)

geom_fox (4)

>> geom_fox (4) ( FreeBSD man: Специальные файлы /dev/* )

BSD mandoc

NAME

geom_fox

 - GEOM based basic disk multipathing

SYNOPSIS

To compile this driver into the kernel, place the following line in your kernel configuration file:

options GEOM_FOX

Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:

geom_fox_load="YES"

DESCRIPTION

The intent of the framework is to provide basic multipathing support to access direct access devices. Basic in the above sentence should be read as: only provides path failover functionality, not load balancing over the available paths etc. Using suitable hardware like SCSI or FibreChannel disks it is possible to have multiple (typically 2) host bus adapters access the same physical disk drive.

Without a multipathing driver the Fx kernel would probe the disks multiple times, resulting in the creation of multiple /dev entries for the same underlying physical device. A unique label written in the GEOM label area allows to detect multiple paths. Using this information it creates a unique da#.fox device.

The device is subsequently used by the Fx kernel to access the disks. Multiple physical access paths ensure that even in case of a path failure the Fx kernel can continue to access the data.

The driver will disallow write operations to the underlying devices once the fox device has been opened for writing.

EXAMPLES

needs a label on the disk as follows in order to work properly:
```
"0123456789abcdef0123456789abcdef"
"GEOM::FOX       <--unique--id-->"
```
For the unique ID 16 bytes are available. The ``GEOM::FOX '' is the magic to mark a device.
The actual labelling is accomplished by
```
echo "GEOM::FOX       someid" | dd of=/dev/da2 conv=sync
```
For FibreChannel devices it is suggested to use the Node World Wide Name (Node WWN) as this is guaranteed by the FibreChannel standard to be worldwide unique. The use of the Port WWN not recommended as each port of a given device has a different WWN, thereby confusing things.
The Node WWN can be obtained from a verbose boot as in for example
```
isp1: Target 1 (Loop 0x1) Port ID 0xe8 (role Target) Arrived
 Port WWN 0x21000004cfc8aca2
 Node WWN 0x20000004cfc8aca2
```
This Node WWN would then be used like so:
```
echo "GEOM::FOX       20000004cfc8aca2" | dd of=/dev/da2 conv=sync
```
For non-FibreChannel devices you could for example use the serial number of the device. Regardless of what you use, make sure the label is unique.
Once the labelling has been performed and assuming the module is loaded the kernel will inform you that it has found a new device with a message similar to
```
Creating new fox (da2)
fox da2.fox lock 0xfffffc0000fdba20
```

To check which physical devices match a given device:

# geom fox list
Geom name: da2.fox
Providers:
1. Name: da2.fox
   Mediasize: 73407865344 (68G)
   Sectorsize: 512
   Mode: r0w0e0
Consumers:
1. Name: da2
   Mediasize: 73407865856 (68G)
   Sectorsize: 512
   Mode: r0w0e0
2. Name: da6
   Mediasize: 73407865856 (68G)
   Sectorsize: 512
   Mode: r0w0e0

To check the status of the components:

# geom fox status
   Name  Status  Components
da2.fox     N/A  da2
                 da6

CAVEATS

The driver depends on the underlying hardware drivers to do the right thing in case of a path failure. If for example a hardware driver continues to retry forever, is not able to re-initiate the I/O to an alternative physical path.

You have to be very sure to provide a unique label for each of the devices. Safety belts are not provided. For FibreChannel devices it is suggested to use the Port WWN of the device. The World Wide Name is guaranteed to be worldwide unique per the FibreChannel standard.