The OpenNET Project / Index page

[ новости /+++ | форум | wiki | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

umass (4)
  • >> umass (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc
     

    NAME

    
    
    umass
    
     - USB Mass Storage Devices driver
    
     
    

    SYNOPSIS

    To compile this driver into the kernel, place the following line in your kernel configuration file:
    device umass

    Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:

    umass_load="YES"
    
     

    DESCRIPTION

    The driver provides support for Mass Storage devices that attach to the USB port.

    To use the driver, usb(4) and one of uhci(4) or ohci(4) must be configured in the kernel. Additionally, since uses the SCSI subsystem and sometimes acts as a SCSI device, it requires da(4) and scbus(4) to be included in the kernel.  

    HARDWARE

    The driver supports USB Mass Storage devices, including:

    Among the supported digital cameras are:

     

    EXAMPLES

    device umass
    device scbus
    device da
    device pass
    

    Add the driver to the kernel.

    "camcontrol rescan 0"

    Rescan a Zip drive that was added after boot. The command above assumes that the Zip drive is on the first SCSI bus in the system.

    camcontrol rescan 0:0:0
    camcontrol rescan 0:0:1
    camcontrol rescan 0:0:2
    camcontrol rescan 0:0:3
    

    Rescan all slots on a multi-slot flash reader, where the slots map to separate LUNs on a single SCSI ID. Typically only the first slot will be enabled at boot time. Again, this assumes that the flash reader is the first SCSI bus in the system.

    bsdlabel -w da0 zip100
    newfs da0c
    mount -t ufs /dev/da0c /mnt
    

    Write a disklabel to the Zip drive (see vpo(4) for the disktab(5) entry), creates the file system and mounts the new file system on /mnt.

    "newfs_msdos /dev/da0"

    Create a new FAT type file system. Care should be taken not to run newfs(8) on devices that already contain data, as this will result in the information being lost.

    Many consumer devices such as digital cameras automatically create MS-DOS based file systems when storing information such as images and videos. These file systems can be accessed by specifying the file system type as msdos when using mount(8).  

    SEE ALSO

    ehci(4), ohci(4), uhci(4), usb(4), vpo(4), disktab(5), bsdlabel(8), camcontrol(8)  

    AUTHORS

    An -nosplit The driver was written by An MAEKAWA Masahide Aq bishop@rr.iij4u.or.jp and An Nick Hibma Aq n_hibma@FreeBSD.org .

    This manual page was written by An Nick Hibma Aq n_hibma@FreeBSD.org .


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    HARDWARE
    EXAMPLES
    SEE ALSO
    AUTHORS


    Поиск по тексту MAN-ов: 




    Спонсоры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2022 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру