The OpenNET Project / Index page

[ новости /+++ | форум | wiki | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

telnetd (8)
  • >> telnetd (8) ( FreeBSD man: Команды системного администрирования )
  • telnetd (8) ( Linux man: Команды системного администрирования )

  • BSD mandoc
     

    NAME

    
    
    telnetd
    
     - DARPA
    
    TELNET
    
    protocol server
     
    

    SYNOPSIS

    /usr/libexec/telnetd [-46BUhlkn ] [-D debugmode ] [-S tos ] [-X authtype ] [-a authmode ] [-edebug ] [-p loginprog ] [-u len ] [-debug [port ] ]  

    DESCRIPTION

    The /usr/libexec/telnetd command is a server which supports the DARPA standard TELNET virtual terminal protocol. Telnetd is normally invoked by the internet server (see inetd(8)) for requests to connect to the TELNET port as indicated by the /etc/services file (see services(5)). The -debug option may be used to start up /usr/libexec/telnetd manually, instead of through inetd(8). If started up this way, port may be specified to run /usr/libexec/telnetd on an alternate TCP port number.

    The /usr/libexec/telnetd command accepts the following options:

    -4
    Forces /usr/libexec/telnetd to use IPv4 addresses only.
    -6
    Forces /usr/libexec/telnetd to use IPv6 addresses only.
    -a authmode
    This option may be used for specifying what mode should be used for authentication. Note that this option is only useful if /usr/libexec/telnetd has been compiled with support for the AUTHENTICATION option. There are several valid values for authmode

    debug
    Turn on authentication debugging code.
    user
    Only allow connections when the remote user can provide valid authentication information to identify the remote user, and is allowed access to the specified account without providing a password.
    valid
    Only allow connections when the remote user can provide valid authentication information to identify the remote user. The login(1) command will provide any additional user verification needed if the remote user is not allowed automatic access to the specified account.
    other
    Only allow connections that supply some authentication information. This option is currently not supported by any of the existing authentication mechanisms, and is thus the same as specifying -a valid
    none
    This is the default state. Authentication information is not required. If no or insufficient authentication information is provided, then the login(1) program will provide the necessary user verification.
    off
    Disable the authentication code. All user verification will happen through the login(1) program.

    -B
    Specify bftp server mode. In this mode, /usr/libexec/telnetd causes login to start a bftp(1) session rather than the user's normal shell. In bftp daemon mode normal logins are not supported, and it must be used on a port other than the normal TELNET port.
    -D debugmode
    This option may be used for debugging purposes. This allows /usr/libexec/telnetd to print out debugging information to the connection, allowing the user to see what /usr/libexec/telnetd is doing. There are several possible values for debugmode

    options
    Print information about the negotiation of TELNET options.
    report
    Print the options information, plus some additional information about what processing is going on.
    netdata
    Display the data stream received by .
    ptydata
    Display data written to the pty.
    exercise
    Has not been implemented yet.

    -debug
    Enable debugging on each socket created by /usr/libexec/telnetd (see SO_DEBUG in socket(2)).
    -edebug
    If /usr/libexec/telnetd has been compiled with support for data encryption, then the -edebug option may be used to enable encryption debugging code.
    -h
    Disable the printing of host-specific information before login has been completed.
    -k
    This option is only useful if /usr/libexec/telnetd has been compiled with both linemode and kludge linemode support. If the -k option is specified, then if the remote client does not support the LINEMODE option, then /usr/libexec/telnetd will operate in character at a time mode. It will still support kludge linemode, but will only go into kludge linemode if the remote client requests it. (This is done by the client sending DONT SUPPRESS-GO-AHEAD and DONT ECHO . The -k option is most useful when there are remote clients that do not support kludge linemode, but pass the heuristic (if they respond with WILL TIMING-MARK in response to a DO TIMING-MARK for kludge linemode support.
    -l
    Specify line mode. Try to force clients to use line-at-a-time mode. If the LINEMODE option is not supported, it will go into kludge linemode.
    -n
    Disable TCP keep-alives. Normally /usr/libexec/telnetd enables the TCP keep-alive mechanism to probe connections that have been idle for some period of time to determine if the client is still there, so that idle connections from machines that have crashed or can no longer be reached may be cleaned up.
    -p loginprog
    Specify an alternate login(1) command to run to complete the login. The alternate command must understand the same command arguments as the standard login.
    -S tos
    Sets the IP type-of-service (TOS) option for the telnet connection to the value tos which can be a numeric TOS value or, on systems that support it, a symbolic TOS name found in the /etc/iptos file.
    -u len
    This option is used to specify the size of the field in the utmp structure that holds the remote host name. If the resolved host name is longer than len the dotted decimal value will be used instead. This allows hosts with very long host names that overflow this field to still be uniquely identified. Specifying -u0 indicates that only dotted decimal addresses should be put into the utmp file.
    -U
    This option causes /usr/libexec/telnetd to refuse connections from addresses that cannot be mapped back into a symbolic name via the gethostbyaddr(3) routine.
    -X authtype
    This option is only valid if /usr/libexec/telnetd has been built with support for the authentication option. It disables the use of authtype authentication, and can be used to temporarily disable a specific authentication type without having to recompile .

    Telnetd operates by allocating a pseudo-terminal device (see pty(4)) for a client, then creating a login process which has the slave side of the pseudo-terminal as stdin stdout and stderr Telnetd manipulates the master side of the pseudo-terminal, implementing the TELNET protocol and passing characters between the remote client and the login process.

    When a TELNET session is started up, /usr/libexec/telnetd sends TELNET options to the client side indicating a willingness to do the following TELNET options, which are described in more detail below:

    DO AUTHENTICATION
    WILL ENCRYPT
    DO TERMINAL TYPE
    DO TSPEED
    DO XDISPLOC
    DO NEW-ENVIRON
    DO ENVIRON
    WILL SUPPRESS GO AHEAD
    DO ECHO
    DO LINEMODE
    DO NAWS
    WILL STATUS
    DO LFLOW
    DO TIMING-MARK
    

    The pseudo-terminal allocated to the client is configured to operate in ``cooked'' mode, and with XTABS and CRMOD enabled (see tty(4)).

    Telnetd has support for enabling locally the following TELNET options:

    "WILL ECHO"
    When the LINEMODE option is enabled, a WILL ECHO or WONT ECHO will be sent to the client to indicate the current state of terminal echoing. When terminal echo is not desired, a WILL ECHO is sent to indicate that /usr/libexec/telnetd will take care of echoing any data that needs to be echoed to the terminal, and then nothing is echoed. When terminal echo is desired, a WONT ECHO is sent to indicate that /usr/libexec/telnetd will not be doing any terminal echoing, so the client should do any terminal echoing that is needed.
    "WILL BINARY"
    Indicate that the client is willing to send a 8 bits of data, rather than the normal 7 bits of the Network Virtual Terminal.
    "WILL SGA"
    Indicate that it will not be sending IAC GA go ahead, commands.
    "WILL STATUS"
    Indicate a willingness to send the client, upon request, of the current status of all TELNET options.
    "WILL TIMING-MARK"
    Whenever a DO TIMING-MARK command is received, it is always responded to with a WILL TIMING-MARK
    "WILL LOGOUT"
    When a DO LOGOUT is received, a WILL LOGOUT is sent in response, and the TELNET session is shut down.
    "WILL ENCRYPT"
    Only sent if /usr/libexec/telnetd is compiled with support for data encryption, and indicates a willingness to decrypt the data stream.

    Telnetd has support for enabling remotely the following TELNET options:

    "DO BINARY"
    Sent to indicate that /usr/libexec/telnetd is willing to receive an 8 bit data stream.
    "DO LFLOW"
    Requests that the client handle flow control characters remotely.
    "DO ECHO"
    This is not really supported, but is sent to identify a BSD 4.2 telnet(1) client, which will improperly respond with WILL ECHO If a WILL ECHO is received, a DONT ECHO will be sent in response.
    "DO TERMINAL-TYPE"
    Indicate a desire to be able to request the name of the type of terminal that is attached to the client side of the connection.
    "DO SGA"
    Indicate that it does not need to receive IAC GA the go ahead command.
    "DO NAWS"
    Requests that the client inform the server when the window (display) size changes.
    "DO TERMINAL-SPEED"
    Indicate a desire to be able to request information about the speed of the serial line to which the client is attached.
    "DO XDISPLOC"
    Indicate a desire to be able to request the name of the X Window System display that is associated with the telnet client.
    "DO NEW-ENVIRON"
    Indicate a desire to be able to request environment variable information, as described in RFC 1572.
    "DO ENVIRON"
    Indicate a desire to be able to request environment variable information, as described in RFC 1408.
    "DO LINEMODE"
    Only sent if /usr/libexec/telnetd is compiled with support for linemode, and requests that the client do line by line processing.
    "DO TIMING-MARK"
    Only sent if /usr/libexec/telnetd is compiled with support for both linemode and kludge linemode, and the client responded with WONT LINEMODE If the client responds with WILL TM the it is assumed that the client supports kludge linemode. Note that the [-k ] option can be used to disable this.
    "DO AUTHENTICATION"
    Only sent if /usr/libexec/telnetd is compiled with support for authentication, and indicates a willingness to receive authentication information for automatic login.
    "DO ENCRYPT"
    Only sent if /usr/libexec/telnetd is compiled with support for data encryption, and indicates a willingness to decrypt the data stream.

     

    NOTES

    By default /usr/libexec/telnetd will read the he hn and im capabilities from /etc/gettytab and use that information (if present) to determine what to display before the login: prompt. You can also use a System V style /etc/issue file by using the if capability, which will override im The information specified in either im or if will be displayed to both console and remote logins.  

    FILES

    /etc/services
    /etc/gettytab
    /etc/iptos
    (if supported)
    /usr/ucb/bftp
    (if supported)

     

    SEE ALSO

    bftp(1), login(1), telnet(1) (if supported), gettytab(5)  

    STANDARDS

    RFC-854
    TELNET PROTOCOL SPECIFICATION
    RFC-855
    TELNET OPTION SPECIFICATIONS
    RFC-856
    TELNET BINARY TRANSMISSION
    RFC-857
    TELNET ECHO OPTION
    RFC-858
    TELNET SUPPRESS GO AHEAD OPTION
    RFC-859
    TELNET STATUS OPTION
    RFC-860
    TELNET TIMING MARK OPTION
    RFC-861
    TELNET EXTENDED OPTIONS - LIST OPTION
    RFC-885
    TELNET END OF RECORD OPTION
    RFC-1073
    Telnet Window Size Option
    RFC-1079
    Telnet Terminal Speed Option
    RFC-1091
    Telnet Terminal-Type Option
    RFC-1096
    Telnet X Display Location Option
    RFC-1123
    Requirements for Internet Hosts -- Application and Support
    RFC-1184
    Telnet Linemode Option
    RFC-1372
    Telnet Remote Flow Control Option
    RFC-1416
    Telnet Authentication Option
    RFC-1411
    Telnet Authentication: Kerberos Version 4
    RFC-1412
    Telnet Authentication: SPX
    RFC-1571
    Telnet Environment Option Interoperability Issues
    RFC-1572
    Telnet Environment Option

     

    HISTORY

    IPv6 support was added by WIDE/KAME project.  

    BUGS

    Some TELNET commands are only partially implemented.

    Because of bugs in the original BSD 4.2 telnet(1), /usr/libexec/telnetd performs some dubious protocol exchanges to try to discover if the remote client is, in fact, a BSD 4.2 telnet(1).

    Binary mode has no common interpretation except between similar operating systems (Unix in this case).

    The terminal type name received from the remote client is converted to lower case.

    Telnetd never sends TELNET IAC GA (go ahead) commands.


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    NOTES
    FILES
    SEE ALSO
    STANDARDS
    HISTORY
    BUGS


    Поиск по тексту MAN-ов: 




    Спонсоры:
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2021 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру