The OpenNET Project / Index page

[ новости /+++ | форум | wiki | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 [Cписок руководств | Печать]

pfsync (4)
  • >> pfsync (4) ( FreeBSD man: Специальные файлы /dev/* )

  • BSD mandoc


     - packet filter state table logging interface


    device pfsync  


    The interface is a pseudo-device which exposes certain changes to the state table used by pf(4). If configured with a physical synchronisation interface, will send state changes out on that interface using IP multicast, and insert state changes received on that interface from other systems into the state table.

    By default, all local changes to the state table are exposed via . However, state changes from packets received by over the network are not rebroadcast. States created by a rule marked with the no-sync keyword are omitted from the interface (see pf.conf5 for details).

    The interface will attempt to collapse multiple updates of the same state into one message where possible. The maximum number of times this can be done before the update is sent out is controlled by the maxupd parameter to ifconfig (see ifconfig(8) and the example below for more details).

    Each packet retrieved on this interface has a header associated with it of length PFSYNC_HDRLEN The header indicates the version of the protocol, address family, action taken on the following states, and the number of state table entries attached in this packet. This structure is defined in Aq Pa net/if_pfsync.h as:

    struct pfsync_header {
            u_int8_t version;
            u_int8_t af;
            u_int8_t action;
            u_int8_t count;


    States can be synchronised between two or more firewalls using this interface, by specifying a synchronisation interface using ifconfig(8). For example, the following command sets fxp0 as the synchronisation interface:
    # ifconfig pfsync0 syncdev fxp0

    It is important that the underlying synchronisation interface is up and has an IP address assigned.

    By default, state change messages are sent out on the synchronisation interface using IP multicast packets. The protocol is IP protocol 240, PFSYNC, and the multicast group used is When a peer address is specified using the syncpeer keyword, the peer address is used as a destination for the pfsync traffic, and the traffic can then be protected using ipsec(4). In such a configuration, the syncdev should be set to the enc(4) interface, as this is where the traffic arrives when it is decapsulated, e.g.:

    # ifconfig pfsync0 syncpeer syncdev enc0

    It is important that the pfsync traffic be well secured as there is no authentication on the protocol and it would be trivial to spoof packets which create states, bypassing the pf ruleset. Either run the pfsync protocol on a trusted network - ideally a network dedicated to pfsync messages such as a crossover cable between two firewalls, or specify a peer address and protect the traffic with ipsec(4).

    For to start its operation automatically at the system boot time, pfsync_enable and pfsync_syncdev variables should be used in rc.conf5. It is not advisable to set up with common network interface configuration variables of rc.conf5 because must start after its syncdev which cannot be always ensured in the latter case.  


    and carp(4) can be used together to provide automatic failover of a pair of firewalls configured in parallel. One firewall handles all traffic - if it dies or is shut down, the second firewall takes over automatically.

    Both firewalls in this example have three sis(4) interfaces. sis0 is the external interface, on the subnet; sis1 is the internal interface, on the subnet; and sis2 is the interface, using the subnet. A crossover cable connects the two firewalls via their sis2 interfaces. On all three interfaces, firewall A uses the .254 address, while firewall B uses .253. The interfaces are configured as follows (firewall A unless otherwise indicated):

    Interfaces configuration in /etc/rc.conf

    network_interfaces="lo0 sis0 sis1 sis2"
    cloned_interfaces="carp0 carp1"
    ifconfig_carp0="vhid 1 pass foo"
    ifconfig_carp1="vhid 2 pass bar"

    pf(4) must also be configured to allow and carp(4) traffic through. The following should be added to the top of /etc/pf.conf

    pass quick on { sis2 } proto pfsync
    pass on { sis0 sis1 } proto carp

    If it is preferable that one firewall handle the traffic, the advskew on the backup firewall's carp(4) interfaces should be set to something higher than the primary's. For example, if firewall B is the backup, its carp1 configuration would look like this:

    ifconfig_carp1="vhid 2 pass bar advskew 100"

    The following must also be added to /etc/sysctl.conf



    Possibility to view state changes using tcpdump(1) has not been ported from Ox yet.  


    bpf(4), carp(4), ifconfig(8), inet(4), inet6(4), ipsec(4), netintro(4), pf(4), pf.conf5, protocols(5), rc.conf5 ifconfig(8), ifstated(8), tcpdump(8)  


    The device first appeared in Ox 3.3 . The device was imported to Fx 5.3 .




    Поиск по тексту MAN-ов: 

    Inferno Solutions
    Hosting by

    Закладки на сайте
    Проследить за страницей
    Created 1996-2023 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру