Исходное сообщение
"как на 2811 из конфига прописать VLAN?" Отправлено SergTel, 16-Июн-08 12:17
Вот полный лог с консоли с твоими настройками: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1) Copyright (c) 2000 by cisco Systems, Inc. cisco 2811 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory Self decompressing the image : ########################################################################## [OK]               Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.            cisco Systems, Inc.            170 West Tasman Drive            San Jose, California 95134-1706 Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.3(14)T7, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Wed 22-Mar-06 18:40 by pt_team Image text-base: 0x40095498, data-base: 0x414E0000 cisco 2811 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory Processor board ID JAD05190MTZ (4292891495) M860 processor: part number 0, mask 49 6 FastEthernet/IEEE 802.3 interface(s) 239K bytes of non-volatile configuration memory. 62720K bytes of processor board System flash (Read/Write) Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.3(14)T7, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Wed 22-Mar-06 18:40 by pt_team          --- System Configuration Dialog --- Continue with configuration dialog? [yes/no]: n Press RETURN to get started! Router>en Router#sh run Building configuration... Current configuration : 492 bytes ! version 12.3 no service password-encryption ! hostname Router ! ! ! ! interface FastEthernet0/0 no ip address duplex auto speed auto shutdown ! interface FastEthernet0/1 no ip address duplex auto speed auto shutdown ! interface FastEthernet0/0/0 shutdown ! interface FastEthernet0/0/1 shutdown ! interface FastEthernet0/0/2 shutdown ! interface FastEthernet0/0/3 shutdown ! interface Vlan1 no ip address shutdown ! ip classless ! ! ! Router#conf t Enter configuration commands, one per line.  End with CNTL/Z. Router(config)#exit %SYS-5-CONFIG_I: Configured from console by console Router#exit Router con0 is now available Press RETURN to get started. Router>en Router#vlan database % Warning: It is recommended to configure VLAN from config mode,   as VLAN database mode is being deprecated. Please consult user   documentation for configuring VTP/VLAN in config mode. Router(vlan)# Router(vlan)#vlan 2 name Rukovodstvo VLAN 2 modified:     Name: Rukovodstvo Router(vlan)# Router(vlan)#vlan 3 name Bugalter VLAN 3 modified:     Name: Bugalter Router(vlan)# Router(vlan)#vlan 10 name Over VLAN 10 added:     Name: Over Router(vlan)# Router(vlan)#exit APPLY completed. Exiting.... Router#conf t Enter configuration commands, one per line.  End with CNTL/Z. Router(config)#interface FastEthernet0/0 Router(config-if)# Router(config-if)#!     Router(config-if)# Router(config-if)#description Link_to_LAN Router(config-if)# Router(config-if)#duplex auto Router(config-if)# Router(config-if)#speed auto Router(config-if)# Router(config-if)#interface Vlan2 %LINK-5-CHANGED: Interface Vlan2, changed state to upRouter(config-if)# Router(config-if)#description Rukovodstvo Router(config-if)# Router(config-if)#ip address 10.0.2.1 255.255.255.0 Router(config-if)# Router(config-if)#interface Vlan3 %LINK-5-CHANGED: Interface Vlan3, changed state to upRouter(config-if)# Router(config-if)#description Bugalter Router(config-if)# Router(config-if)#ip address 10.0.3.1 255.255.255.0 Router(config-if)# Router(config-if)#interface Vlan10 %LINK-5-CHANGED: Interface Vlan10, changed state to upRouter(config-if)# Router(config-if)#description Over Router(config-if)# Router(config-if)#ip address 10.0.10.1 255.255.255.0 Router(config-if)# Router(config-if)# Router(config-if)# Router(config-if)#!    HWIC-4ESW Router(config-if)# Router(config-if)#interface FastEthernet0/0/0 Router(config-if)# Router(config-if)#switchport access vlan 2 Router(config-if)# Router(config-if)#interface FastEthernet0/0/1 Router(config-if)# Router(config-if)#switchport access vlan 3 Router(config-if)# Router(config-if)#interface FastEthernet0/0/3 Router(config-if)# Router(config-if)#switchport access vlan 10 Router(config-if)# Router(config-if)# Router(config-if)# Router(config-if)#exit Router(config)#exit %SYS-5-CONFIG_I: Configured from console by console Router#wri Destination filename [startup-config]? Building configuration... [OK] Router#sh vlan VLAN Name                             Status    Ports ---- -------------------------------- --------- ------------------------------- 1    default                          active    Fa0/0/2 2    Rukovodstvo                      active    Fa0/0/0 3    Bugalter                         active    Fa0/0/1 4    v4                               active     10   Over                             active    Fa0/0/3 1002 fddi-default                     active     1003 token-ring-default               active     1004 fddinet-default                  active     1005 trnet-default                    active     VLAN Type  SAID       MTU   Parent RingNo BridgeNo Stp  BrdgMode Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ 1    enet  100001     1500  -      -      -        -    -        0      0 2    enet  100002     1500  -      -      -        -    -        0      0 3    enet  100003     1500  -      -      -        -    -        0      0 4    enet  100004     1500  -      -      -        -    -        0      0 10   enet  100010     1500  -      -      -        -    -        0      0 1002 enet  101002     1500  -      -      -        -    -        0      0 1003 enet  101003     1500  -      -      -        -    -        0      0 1004 enet  101004     1500  -      -      -        -    -        0      0 1005 enet  101005     1500  -      -      -        -    -        0      0 Router#dir Directory of flash:/     1  -rw-     5571584          <no date>  c2800nm-ipbase-mz.123-14.T7.bin     2  -rw-         796          <no date>  vlan.dat 32514048 bytes total (26941668 bytes free) Router#reload Proceed with reload? [confirm] %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command. System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1) Copyright (c) 2000 by cisco Systems, Inc. cisco 2811 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory Self decompressing the image : ########################################################################## [OK]               Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.            cisco Systems, Inc.            170 West Tasman Drive            San Jose, California 95134-1706 Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.3(14)T7, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Wed 22-Mar-06 18:40 by pt_team Image text-base: 0x40095498, data-base: 0x414E0000 cisco 2811 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory Processor board ID JAD05190MTZ (4292891495) M860 processor: part number 0, mask 49 6 FastEthernet/IEEE 802.3 interface(s) 239K bytes of non-volatile configuration memory. 62720K bytes of processor board System flash (Read/Write) Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.3(14)T7, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Wed 22-Mar-06 18:40 by pt_team %LINK-5-CHANGED: Interface Vlan1, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down %LINK-5-CHANGED: Interface Vlan1, changed state to administratively down %LINK-5-CHANGED: Interface Vlan2, changed state to up %LINK-5-CHANGED: Interface Vlan3, changed state to up %LINK-5-CHANGED: Interface Vlan10, changed state to up Press RETURN to get started! Router>en Router#sh run Building configuration... Current configuration : 822 bytes ! version 12.3 no service password-encryption ! hostname Router ! ! ! ! interface FastEthernet0/0 description Link_to_LAN no ip address duplex auto speed auto shutdown ! interface FastEthernet0/1 no ip address duplex auto speed auto shutdown ! interface FastEthernet0/0/0 switchport access vlan 2 shutdown ! interface FastEthernet0/0/1 switchport access vlan 3 shutdown ! interface FastEthernet0/0/2 shutdown ! interface FastEthernet0/0/3 switchport access vlan 10 shutdown ! interface Vlan1 no ip address shutdown ! interface Vlan2 description Rukovodstvo ip address 10.0.2.1 255.255.255.0 ! interface Vlan3 description Bugalter ip address 10.0.3.1 255.255.255.0 ! interface Vlan10 description Over ip address 10.0.10.1 255.255.255.0 ! ip classless ! ! ! ! line con 0 line vty 0 4 login ! ! end

Ваше сообщение
Имя*:
EMail:	Для отправки новых сообщений в текущей нити на email укажите знак ! перед адресом, например, !user@host.ru (!! - не показывать email). Более тонкая настройка отправки ответов производится в профиле зарегистрированного участника форума.
Заголовок*:
Сообщение*:	> Вот полный лог с консоли с твоими настройками: > System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1) > Copyright (c) 2000 by cisco Systems, Inc. > cisco 2811 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory > Self decompressing the image : > ########################################################################## [OK] > > Restricted Rights Legend > Use, duplication, or disclosure by the Government is > subject to restrictions as set forth in subparagraph > (c) of the Commercial Computer Software - Restricted > Rights clause at FAR sec. 52.227-19 and subparagraph > (c) (1) (ii) of the Rights in Technical Data and Computer > Software clause at DFARS sec. 252.227-7013. > cisco > Systems, Inc. > 170 > West Tasman Drive > San > Jose, California 95134-1706 > Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.3(14)T7, RELEASE SOFTWARE > (fc2) > Technical Support: http://www.cisco.com/techsupport > Copyright (c) 1986-2006 by Cisco Systems, Inc. > Compiled Wed 22-Mar-06 18:40 by pt_team > Image text-base: 0x40095498, data-base: 0x414E0000 > cisco 2811 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory > Processor board ID JAD05190MTZ (4292891495) > M860 processor: part number 0, mask 49 > 6 FastEthernet/IEEE 802.3 interface(s) > 239K bytes of non-volatile configuration memory. > 62720K bytes of processor board System flash (Read/Write) > Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.3(14)T7, RELEASE SOFTWARE > (fc2) > Technical Support: http://www.cisco.com/techsupport > Copyright (c) 1986-2006 by Cisco Systems, Inc. > Compiled Wed 22-Mar-06 18:40 by pt_team > --- System Configuration > Dialog --- > Continue with configuration dialog? [yes/no]: n > Press RETURN to get started! > Router>en > Router#sh run > Building configuration... > Current configuration : 492 bytes > ! > version 12.3 > no service password-encryption > ! > hostname Router > ! > ! > ! > ! > interface FastEthernet0/0 > no ip address > duplex auto > speed auto > shutdown > ! > interface FastEthernet0/1 > no ip address > duplex auto > speed auto > shutdown > ! > interface FastEthernet0/0/0 > shutdown > ! > interface FastEthernet0/0/1 > shutdown > ! > interface FastEthernet0/0/2 > shutdown > ! > interface FastEthernet0/0/3 > shutdown > ! > interface Vlan1 > no ip address > shutdown > ! > ip classless > ! > ! > ! > Router#conf t > Enter configuration commands, one per line. End with CNTL/Z. > Router(config)#exit > %SYS-5-CONFIG_I: Configured from console by console > Router#exit > Router con0 is now available > Press RETURN to get started. > Router>en > Router#vlan database > % Warning: It is recommended to configure VLAN from config mode, > as VLAN database mode is being deprecated. Please consult user > documentation for configuring VTP/VLAN in config mode. > Router(vlan)# > Router(vlan)#vlan 2 name Rukovodstvo > VLAN 2 modified: > Name: Rukovodstvo > Router(vlan)# > Router(vlan)#vlan 3 name Bugalter > VLAN 3 modified: > Name: Bugalter > Router(vlan)# > Router(vlan)#vlan 10 name Over > VLAN 10 added: > Name: Over > Router(vlan)# > Router(vlan)#exit > APPLY completed. > Exiting.... > Router#conf t > Enter configuration commands, one per line. End with CNTL/Z. > Router(config)#interface FastEthernet0/0 > Router(config-if)# > Router(config-if)#! > Router(config-if)# > Router(config-if)#description Link_to_LAN > Router(config-if)# > Router(config-if)#duplex auto > Router(config-if)# > Router(config-if)#speed auto > Router(config-if)# > Router(config-if)#interface Vlan2 > %LINK-5-CHANGED: Interface Vlan2, changed state to upRouter(config-if)# > Router(config-if)#description Rukovodstvo > Router(config-if)# > Router(config-if)#ip address 10.0.2.1 255.255.255.0 > Router(config-if)# > Router(config-if)#interface Vlan3 > %LINK-5-CHANGED: Interface Vlan3, changed state to upRouter(config-if)# > Router(config-if)#description Bugalter > Router(config-if)# > Router(config-if)#ip address 10.0.3.1 255.255.255.0 > Router(config-if)# > Router(config-if)#interface Vlan10 > %LINK-5-CHANGED: Interface Vlan10, changed state to upRouter(config-if)# > Router(config-if)#description Over > Router(config-if)# > Router(config-if)#ip address 10.0.10.1 255.255.255.0 > Router(config-if)# > Router(config-if)# > Router(config-if)# > Router(config-if)#! HWIC-4ESW > Router(config-if)# > Router(config-if)#interface FastEthernet0/0/0 > Router(config-if)# > Router(config-if)#switchport access vlan 2 > Router(config-if)# > Router(config-if)#interface FastEthernet0/0/1 > Router(config-if)# > Router(config-if)#switchport access vlan 3 > Router(config-if)# > Router(config-if)#interface FastEthernet0/0/3 > Router(config-if)# > Router(config-if)#switchport access vlan 10 > Router(config-if)# > Router(config-if)# > Router(config-if)# > Router(config-if)#exit > Router(config)#exit > %SYS-5-CONFIG_I: Configured from console by console > Router#wri > Destination filename [startup-config]? > Building configuration... > [OK] > Router#sh vlan > VLAN Name > > Status > Ports > ---- -------------------------------- --------- ------------------------------- > 1 default > > active > Fa0/0/2 > 2 Rukovodstvo > > active Fa0/0/0 > 3 Bugalter > > active Fa0/0/1 > 4 v4 > > > active > 10 Over > > active > Fa0/0/3 > 1002 fddi-default > active > 1003 token-ring-default > active > 1004 fddinet-default > active > 1005 trnet-default > active > VLAN Type SAID MTU > Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2 > ---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------ > 1 enet 100001 1500 > - - > - - > - > 0 0 > 2 enet 100002 1500 > - - > - - > - > 0 0 > 3 enet 100003 1500 > - - > - - > - > 0 0 > 4 enet 100004 1500 > - - > - - > - > 0 0 > 10 enet 100010 1500 > - - > - - > - 0 > 0 > 1002 enet 101002 1500 - > - - > - > - 0 > 0 > 1003 enet 101003 1500 - > - - > - > - 0 > 0 > 1004 enet 101004 1500 - > - - > - > - 0 > 0 > 1005 enet 101005 1500 - > - - > - > - 0 > 0 > Router#dir > Directory of flash:/ > 1 -rw- 5571584 > <no date> > c2800nm-ipbase-mz.123-14.T7.bin > 2 -rw- > 796 > <no date> vlan.dat > 32514048 bytes total (26941668 bytes free) > Router#reload > Proceed with reload? [confirm] > %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command. > System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1) > Copyright (c) 2000 by cisco Systems, Inc. > cisco 2811 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory > Self decompressing the image : > ########################################################################## [OK] > > Restricted Rights Legend > Use, duplication, or disclosure by the Government is > subject to restrictions as set forth in subparagraph > (c) of the Commercial Computer Software - Restricted > Rights clause at FAR sec. 52.227-19 and subparagraph > (c) (1) (ii) of the Rights in Technical Data and Computer > Software clause at DFARS sec. 252.227-7013. > cisco > Systems, Inc. > 170 > West Tasman Drive > San > Jose, California 95134-1706 > Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.3(14)T7, RELEASE SOFTWARE > (fc2) > Technical Support: http://www.cisco.com/techsupport > Copyright (c) 1986-2006 by Cisco Systems, Inc. > Compiled Wed 22-Mar-06 18:40 by pt_team > Image text-base: 0x40095498, data-base: 0x414E0000 > cisco 2811 (MPC860) processor (revision 0x200) with 60416K/5120K bytes of memory > Processor board ID JAD05190MTZ (4292891495) > M860 processor: part number 0, mask 49 > 6 FastEthernet/IEEE 802.3 interface(s) > 239K bytes of non-volatile configuration memory. > 62720K bytes of processor board System flash (Read/Write) > Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.3(14)T7, RELEASE SOFTWARE > (fc2) > Technical Support: http://www.cisco.com/techsupport > Copyright (c) 1986-2006 by Cisco Systems, Inc. > Compiled Wed 22-Mar-06 18:40 by pt_team > %LINK-5-CHANGED: Interface Vlan1, changed state to up > %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up > %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up > %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down > %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down > %LINK-5-CHANGED: Interface Vlan1, changed state to administratively down > %LINK-5-CHANGED: Interface Vlan2, changed state to up > %LINK-5-CHANGED: Interface Vlan3, changed state to up > %LINK-5-CHANGED: Interface Vlan10, changed state to up > Press RETURN to get started! > Router>en > Router#sh run > Building configuration... > Current configuration : 822 bytes > ! > version 12.3 > no service password-encryption > ! > hostname Router > ! > ! > ! > ! > interface FastEthernet0/0 > description Link_to_LAN > no ip address > duplex auto > speed auto > shutdown > ! > interface FastEthernet0/1 > no ip address > duplex auto > speed auto > shutdown > ! > interface FastEthernet0/0/0 > switchport access vlan 2 > shutdown > ! > interface FastEthernet0/0/1 > switchport access vlan 3 > shutdown > ! > interface FastEthernet0/0/2 > shutdown > ! > interface FastEthernet0/0/3 > switchport access vlan 10 > shutdown > ! > interface Vlan1 > no ip address > shutdown > ! > interface Vlan2 > description Rukovodstvo > ip address 10.0.2.1 255.255.255.0 > ! > interface Vlan3 > description Bugalter > ip address 10.0.3.1 255.255.255.0 > ! > interface Vlan10 > description Over > ip address 10.0.10.1 255.255.255.0 > ! > ip classless > ! > ! > ! > ! > line con 0 > line vty 0 4 > login > ! > ! > end
	Введите код, изображенный на картинке: