The OpenNET Project / Index page

[ новости/++ | форум | wiki | теги ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

introu (1)
  • >> introu (1) ( Linux man: Команды и прикладные программы пользовательского уровня )
  •  

    NAME

    introu - introduction to LAM user interface commands
     
    

    LIST OF COMMANDS

    
    Name           Appears        Description
                   on Page
    
    bfctl          bfctl.1        Control message buffers (optional).
    bfstate        bfstate.1      Get message buffer status (optional).
    doom           doom.1         Deliver a signal (optional).
    fctl           fctl.1         Control remote file access (optional).
    fstate         fstate.1       Get remote file status (optional).
    hboot          hboot.1        Start LAM on a local node.
    mpicc          mpicc.1        Compile LAM C programs.
    mpiCC          mpicc.1        Compile LAM C++ programs.
    mpif77         mpif77.1       Compile LAM F77 programs.
    lamboot        lamboot.1      Start LAM.
    lamclean       lamclean.1     Clean all nodes.
    lamexec        lamexec.1      Run non-MPI programs.
    lamgrow        lamgrow.1      Add a node.
    lamhalt        lamhalt.1      Terminate LAM.
    lamshrink      lamshrink.1    Remove a node.
    lamtrace       lamtrace.1     Unload trace data.
    loadgo         loadgo.1       Execute program (optional).
    mpimsg         mpimsg.1       Display MPI buffered messages.
    mpirun         mpirun.1       Run an MPI application.
    mpitask        mpitask.1      Display MPI processes.
    recon          recon.1        Verify LAM setup.
    state          state.1        Get process status (optional).
    sweep          bfctl.1        Clean out message buffers (optional).
    tkill          tkill.1        Terminate local node LAM session.
    tping          tping.1        Echo messages to a node.
    wipe           wipe.1         Terminate LAM (deprecated; use lamhalt).
    
     

    Node Specification

    Target nodes are given on the command line. Nodes are generically identified as n<list>, where <list> can be a single node identifier or a list of node identifiers. For example:

    n1
    n1,3,5-10
    

    Additionally, c<list> can be used to list specific CPUs on a given machine (lamboot(1) is used to specify how many CPUs LAM may use on each node).

    Node/CPU identifiers are established in the boot schema (see bhost(5)), and can be written in decimal or hexadecimal notation. In addition to explicit node identification, LAM has special mnemonics that refer to special nodes or a group of nodes.

    h
    the local node where the command is typed (as in "here")
    o
    the origin node where LAM was started with lamboot(1)
    N
    all nodes
    C
    all CPUs
     

    Process Specification

    LAM processes can be specified in two ways: by process identifier from the underlying operating system or by LAM process index. PIDs are written as p<list>, where <list> can be a single PID or a list of PIDs. Process indices are written as i<list>, where <list> can be a single index or a list of indices.


     

    Index

    NAME
    LIST OF COMMANDS
    Node Specification
    Process Specification


    Поиск по тексту MAN-ов: 




      Закладки на сайте
      Проследить за страницей
    Created 1996-2017 by Maxim Chirkov  
    ДобавитьРекламаВебмастеруГИД  
    Hosting by Ihor