The OpenNET Project / Index page

[ новости /+++ | форум | wiki | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

hubd (7)
  • >> hubd (7) ( Solaris man: Макропакеты и соглашения )
  •  

    NAME

    hubd - USB hub driver
     
    

    SYNOPSIS

    hub@unit-address
    

     

    DESCRIPTION

    The hubd is a USBA (Solaris USB Architecture) compliant client driver that supports USB hubs conforming to the Universal Serial Bus Specification 2.0. The hubd driver supports bus-powered and self-powered hubs. The driver supports hubs with individual port power, ganged power and no power switching.

    When a device is attached to a hub port, the hubd driver enumerates the device by determining its type and assigning an address to it. For multi-configuration devices, hubd sets the preferred configuration (refer to cfgadm_usb(1M) to select a configuration). The hubd driver attaches a driver to the device if one is available for the default or selected configuration. When the device is disconnected from the hub port, the hubd driver offlines any driver instance attached to the device.  

    FILES

    /kernel/drv/hubd

    32- bit x86 ELF kernel module

    /kernel/drv/amd64/hubd

    64- bit x86 ELF kernel module

    /kernel/drv/sparcv9/hubd

    64-bit SPARC ELF kernel module

     

    ATTRIBUTES

    See attributes(5) for a description of the following attributes:

    ATTRIBUTE TYPEATTRIBUTE VALUE

    ArchitectureSPARC, x86, PCI-based systems

    Availability

     

    SEE ALSO

    cfgadm_usb(1M), attributes(5), usba(7D)

    Writing Device Drivers

    Universal Serial Bus Specification 2.0

    System Administration Guide: Basic Administration

    http://www.sun.com/io  

    DIAGNOSTICS

    In addition to being logged, the following messages may also appear on the system console. Messages are formatted in the following manner:

    WARNING: <device path> <hubd<instance number>): Message...
    

    where <instance number> is the instance number of hubd and <device path> is the physical path to the device in /devices directory. Messages from the root hub are displayed with a usb<instance number> prefix instead of hub<instance number> as the root hub is an integrated part of the host controller.

    Connecting device on port <number> failed.

    The driver failed to enumerate the device connected on port <number> of hub. If enumeration fails, disconnect and re-connect.

    Use of a USB 1.0 hub behind a high speed port may cause unexpected failures.

    Devices connected to a USB 1.0 hub which are in turn connected to an external USB 2.0 hub, may misbehave unexpectedly or suddenly go offline. This is due to a documented incompatibility between USB 1.0 hubs and USB 2.0 hub Transaction Translators. Please use only USB 2.0 or USB 1.1 hubs behind high-speed ports.

    Connecting a high speed device to a non-high speed hub (port x) will result in a loss of performance. Please connect the device to a high speed port to get the maximum performance.

    USB 2.0 devices connected to USB 1.0 or 1.1 hubs cannot run at their highest speed, even when the hub is in turn connected to a high-speed port. For best performance, reconnect without going through a USB 1.0 or 1.1 hub.

    Cannot access <device>. Please reconnect.

    This hub has been disconnected because a device other than the original one has been inserted. The driver informs you of this fact by displaying the name of the original device.

    Port <n> overcurrent.

    An overcurrent condition was detected. Please remove the device on this port.

    Devices not identical to the previous one on this port. Please disconnect and reconnect.

    Same condition as described above; however in this case, the driver is unable to identify the original device with a name string.

    Hub driver supports max of <n> ports on hub. Hence, using the first <number of physical ports> of <n> ports available.

    The current hub driver supports hubs that have <n> ports or less. A hub with more than <n> ports has been plugged in. Only the first <n> out of the total <number of physical ports> ports are usable.

    Hub global over current condition, please disconnect the devices connected to the hub to clear the condition. You may need to re-connect the hub if the ports do not work.

    An overcurrent condition was detected on the hub. This         means that the aggregate current
    being drawn by the devices on the downstream ports exceeds a preset value. Refer to section 7.2.1.2 and 11.13 of the Universal Serial Bus Specification 2.0. If this message continues to display, you may need to remove downstream devices to eliminate the problem. If any port does not work after the overcurrent condition is cleared, re-connect the hub to re-enable the ports.

    Root hub over current condition, please check your system to clear the condition as soon as possible. You may need to reboot the system if the root hub does not recover automatically.

    An overcurrent condition was detected on the root hub, indicating that malfunctioning devices on the downstream ports are drawing too much current. Please disconnect the problematic downstream devices to eliminate the problem. If the root hub doesn't work after the overcurrent condition is cleared, you may need to reboot the system.

    The following messages may be logged into the system log. They are formatted in the following manner:

    <device path><hubd<instance number>): message...
    

    Local power has been lost, please disconnect hub.

    A USB self-powered hub has lost external power. All USB devices connected down-stream from this hub will cease to function. Disconnect the hub, plug in the external power-supply and then plug in the hub again.

    Local power has been lost, the hub could draw <x> mA power from the USB bus.

    A USB self/bus-powered hub has lost external power. Some USB devices connected down-stream from this hub may cease to function. Disconnect the external power-supply and then plug in the hub again.

    Two bus-powered hubs cannot be concatenated.

    A bus-powered hub was connected to a bus powered hub port. Please remove this bus-powered hub and connect it to a self-powered hub or a root hub port.

    Configuration <n> for device <device> at port <m> exceeds power available for this port. Please re-insert your device into another hub port which has enough power.

    The device requires more power than is available on this port.

    Port <n> in over current condition, please check the attached device to clear the condition. The system will try to recover the port, but if not successful, you need to re-connect the hub or reboot the system to bring the port back to work.

    An overcurrent condition was detected on port <n>. This means the device connected to the port is drawing more current than the hub can supply. If this message continues to display, please disconnect the device to eliminate the problem. If the port doesn't work after the overcurrent condition is cleared, please re-connect the hub or reboot the system to enable the port again.


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    FILES
    ATTRIBUTES
    SEE ALSO
    DIAGNOSTICS


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру