The OpenNET Project / Index page

[ новости /+++ | форум | wiki | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

elxl (7)
  • >> elxl (7) ( Solaris man: Макропакеты и соглашения )
  •  

    NAME

    elxl - 3Com Ethernet device driver
     
    

    SYNOPSIS

    /kernel/drv/elxl 
    
     

    DESCRIPTION

    The elxl driver currently supports the following network cards: EtherLink XL (3C900-TPO, 3C900-COMBO, 3C900B-TPO, 3C900B-COMBO, and 3C900B-TPC), EtherLink XL 10/100 (3C905-TX Fast, 3C905-T4 Fast, 3C905B-TX Fast, 3C905B-T4 Fast, and 3C905C-TX-M Fast), and EtherLink Server 10/100 (3C980-TX Fast and 3C980C-TXM).

    The elxl Ethernet driver is a multi-threaded, loadable, clonable, STREAMS hardware driver supporting the connectionless Data Link Provider Interface, dlpi(7P). Multiple EtherLink XL controllers installed within the system are supported by the driver. The elxl driver provides basic support for the EtherLink hardware. Functions include chip initialization, frame transmit and receive, multicast and promiscuous mode support, and error recovery and reporting.

    The cloning, character-special device /dev/elxl is used to access all EtherLink devices installed within the system.

    The elxl driver is dependent on /kernel/misc/gld, a loadable kernel module that provides the elxl driver with the DLPI and STREAMS functionality required of a LAN driver. See gld(7D) for more details on the primatives supported by the driver.

    The values returned by the driver in the DL_INFO_ACK primitive in response to the DL_INFO_REQ from the user are as follows:

    * Maximum SDU is 1500 (ETHERMTU).

    * Minimum SDU is 0. The driver will pad to the mandatory 60-octet minimum packet size.

    * The dlsap address length is 8.

    * MAC type is DL_ETHER.

    * The sap length value is -2, meaning the physical address component is followed immediately by a 2-byte sap component within the DLSAP address.

    * The broadcast address value is Ethernet/IEEE broadcast address (FF:FF:FF:FF:FF:FF).

     

    PRECONFIGURE

     

    Supported Settings

    * Media Type: Auto Select

     

    Known Problems and Limitations

    * 3C905B cards in a Compaq ProLiant 6500 can fail to generate interrupts. There is no known workaround for this problem. However, because some slots appear to be more prone to the problem than others, try correcting the problem by moving the card to another PCI slot. If that fails, try rebooting the machine a number of times to free the card from the wedged state.

    * Early versions of the 3Com 3C905C-TX-M adapter firmware do not support PXE network boot on Solaris systems. If you are using a version earlier than 4.11, upgrade the firmware. The PXE version is indicated by the Managed Boot Agent version number. This number is not normally displayed during boot, but is shown on the PXE configuration screen.

     

    CONFIGURATION

    The /kernel/drv/elxl.conf file supports the following tunable properties that you can set in the elxl.conf file:

    tx_start_thresh

    Minimum number of bytes in transmit FIFO (if lower then the packet size), before NIC starts the frame transfer. The higher the value, the less chance for a transmission underrun error that triggers a transmission retry. Default value is 250, maximum value is 1514.

    recv-descriptors

    The number of frames the device may receive from the network without system attention before the device begins dropping the frames. Valid range is 1 to 256. Default is 24.

    xmit-descriptors

    The number of outgoing frames that the system can queue on the driver queue before blocking a send request. Valid range is 1 to 512. Default is 128.

    min-recv-data-buffers

    Minimal number of allocated receive data buffers. Must be equal or greater than effective number of recv-descriptors. Default (max value) is 128.

    max-recv-data-buffers

    Maximum number of allocated receive data buffers. Must be equal or greater then min-recv-data-buffers number.

    inter-frame-space

    Amount of time in addition to the standard inter-frame time used by IEEE 802.3 deference rule. Expressed in 32 multiples of bit time. Used only in half-duplex context. This small IFS is to make the defer-after-transmit time slightly longer than the defer-after-receive time. This greatly reduces the high collision rate seen with heavy TCP traffic (almost exactly one collision per ACK), giving slightly improved overall throughput in half-duplex mode. Default IFS is 32. This property is ignored in full-duplex mode.

    full-duplex

    When set, it forces full-duplex mode for NIC capable of working in full-duplex mode. If this property is set, the auto-negotiation feature (if supported) of the network controller is disabled. For full duplex operation use full-duplex=1. For half duplex use full-duplex=0. Half-duplex operation provides better results on older 10-Mbit networks.

    speed

    Link speed in Mbps. Valid values are 10 and 100. If this property is set, the auto-negotiation feature of the network controller (if supported) is disabled.

     

    FILES

    /dev/elxl Special character device

    /kernel/drv/elxl.conf Configuration file for elxl driver

     

    ATTRIBUTES

    See attributes(5) for descriptions of the following attributes:

    ATTRIBUTE TYPEATTRIBUTE VALUE
    Architecturex86

     

    SEE ALSO

    attributes(5), gld(7D), streamio(7I), dlpi(7P).


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    PRECONFIGURE
    Supported Settings
    Known Problems and Limitations
    CONFIGURATION
    FILES
    ATTRIBUTES
    SEE ALSO


    Поиск по тексту MAN-ов: 




    Партнёры:
    PostgresPro
    Inferno Solutions
    Hosting by Hoster.ru
    Хостинг:

    Закладки на сайте
    Проследить за страницей
    Created 1996-2024 by Maxim Chirkov
    Добавить, Поддержать, Вебмастеру