Интерактивная система просмотра системных руководств (man-ов)
attraction (1) ( Solaris man: Команды и прикладные программы пользовательского уровня )>> attraction (1) ( Linux man: Команды и прикладные программы пользовательского уровня )
attraction - interactions of opposing forces
] [-foreground color
] [-window] [-root] [-mono] [-install]
] [-points int
] [-threshold int
[-mode balls | lines | polygons | splines | filled-splines | tails ]
] [-segments int
] [-delay usecs
] [-radius int
] [-vy int
] [-glow] [-noglow]
[-orbit] [-viscosity float
] [-mouse] [-no-mouse] [-mouse-size]
[-walls] [-nowalls] [-maxspeed] [-nomaxspeed]
program has several visually different modes of
operation, all of which are based on the interactions of a set of control
points which attract each other up to a certain distance, and then begin
to repel each other. The attraction/repulsion is proportional to the
distance between any two particles.
accepts the following options:
Draw on a newly-created window. This is the default.
Draw on the root window.
If on a color display, pretend we're on a monochrome display.
Install a private colormap for the window.
- -visual visual
Specify which visual to use. Legal values are the name of a visual class,
or the id number (decimal or hex) of a specific visual.
- -points integer
How many control points should be used, or 0 to select the number randomly.
Default 0. Between 3 and 15 works best.
- -threshold integer
The distance (in pixels) from each particle at which the attractive force
becomes repulsive. Default 100.
- -mode balls | lines | polygons | tails | splines | filled-splines
In balls mode (the default) the control points are drawn as filled
circles. The larger the circle, the more massive the particle.
In lines mode, the control points are connected by straight lines;
the effect is something like qix.
In polygons mode, the control points are connected by straight
lines, and filled in. This is most interesting in color.
In splines mode, a closed spline is interpolated from the control
In filled-splines mode, the splines are filled in instead of being
outlines. This is most interesting in color.
In tails mode, the path which each particle follows is indicated
by a worm-like trail, whose length is controlled by the segments
- -size integer
The size of the balls in pixels, or 0, meaning to select the sizes
randomly (the default.) If this is specified, then all balls will be
the same size. This option has an effect in all modes, since the ``size''
of the balls controls their mass.
- -segments integer
If in lines or polygons mode, how many sets of line segments
or polygons should be drawn. Default 100. This has no effect in balls
mode. If segments is 0, then no segments will ever be erased (this
is only useful in color.)
- -delay microseconds
How much of a delay should be introduced between steps of the animation.
Default 10000, or about 0.01 seconds.
- -color-shift int
If on a color display, the color of the line segments or polygons will
cycle through the color map. This specifies how many lines will be drawn
before a new color is chosen. (When a small number of colors are available,
increasing this value will yield smoother transitions.) Default 3.
This has no effect in balls mode.
The size in pixels of the circle on which the points are initially positioned.
The default is slightly smaller than the size of the window.
This is consulted only in balls mode. If this is specified, then
the saturation of the colors of the points will vary according to their
current acceleration. This has the effect that the balls flare brighter
when they are reacting to each other most strongly.
In glow mode, all of the balls will be drawn the same (random)
color, modulo the saturation shifts. In non-glow mode, the balls will
each be drawn in a random color that doesn't change.
Don't do ``glowing.'' This is the default.
- -vx pixels
- -vy pixels
Initial velocity of the balls. This has no effect in -orbit mode.
Make the initial force on each ball be tangential to the circle on which
they are initially placed, with the right velocity to hold them in orbit
about each other. After a while, roundoff errors will cause the orbit
- -vmult float
In orbit mode, the initial velocity of the balls is multiplied by this;
a number less than 1 will make the balls pull closer together, and a larger
number will make them move apart. The default is 0.9, meaning a slight
- -viscosity float
This sets the viscosity of the hypothetical fluid through which the control
points move; the default is 1, meaning no resistance. Values higher than 1
aren't interesting; lower values cause less motion.
One interesting thing to try is
attraction -viscosity 0.8 -points 75 \
-mouse -geometry =500x500
Give it a few seconds to settle down into a stable clump, and then move
the mouse through it to make "waves".
This will cause the mouse to be considered a control point; it will not be
drawn, but it will influence the other points, so you can wave the mouse
and influence the images being created.
Turns off -mouse.
- -mouse-size integer
In -mouse mode, this sets the mass of the mouse (analagously to the
This will cause the balls to continue on past the edge of the
screen or window. They will still be kept track of and can come back.
This will cause the balls to bounce when they get
to the edge of the screen or window. This is the default behavior.
Imposes a maximum speed (default). If a ball ends up going faster than
this, it will be treated as though there were .9 viscosity until it is
under the limit. This stops the balls from continually accelerating (which
they have a tendancy to do), but also causes balls moving very fast to
tend to clump in the lower right corner.
If this is specified, no maximum speed is set for the balls.
Uses the old, simple bouncing algorithm (default). This simply moves any
ball that is out of bounds back to a wall and reverses its velocity.
This works fine for most cases, but under some circumstances, the
simplification can lead to annoying effects.
Uses a more intelligent bouncing algorithm. This method actually reflects
the balls off the walls until they are within bounds. This can be slow
if balls are bouncing a whole lot, perhaps because of -nomaxspeed.
- -graphmode none | x | y | both | speed
For "x", "y", and "both", displays the given velocities of each ball as a
bar graph in the same window as the balls. For "speed", displays the total
speed of each ball. Default is "none".
to get the default host and display number.
to get the name of a resource file that overrides the global resources
stored in the RESOURCE_MANAGER property.
Copyright © 1992, 1993, 1997 by Jamie Zawinski. Permission to use, copy,
modify, distribute, and sell this software and its documentation for any
purpose is hereby granted without fee, provided that the above copyright
notice appear in all copies and that both that copyright notice and this
permission notice appear in supporting documentation. No representations are
made about the suitability of this software for any purpose. It is provided
"as is" without express or implied warranty.
Jamie Zawinski <email@example.com
Viscosity and mouse support by Philip Edward Cutone, III.
Walls, speed limit options, new bouncing, graphs, and tail mode fix by
Matthew Strait. 31 March 2001
- SEE ALSO