The OpenNET Project / Index page

[ новости/++ | форум | wiki | теги | ]

Интерактивная система просмотра системных руководств (man-ов)

 ТемаНаборКатегория 
 
 [Cписок руководств | Печать]

trident (4)
  • >> trident (4) ( Linux man: Специальные файлы /dev/* )
  •  

    NAME

    trident - Trident video driver
     
    

    SYNOPSIS

    Section N'34'DeviceN'34'
      Identifier N'34'devnameN'34'
      Driver N'34'tridentN'34'
      ...
    EndSection
    
     

    DESCRIPTION

    trident is an Xorg driver for Trident video cards. The driver is accelerated, and provides support for the following framebuffer depths: 1, 4, 8, 15, 16, and 24. Multi-head configurations are supported. The XvImage extension is supported on TGUI96xx and greater cards.  

    SUPPORTED HARDWARE

    The trident driver supports PCI,AGP and ISA video cards based on the following Trident chips:
    Blade
    Blade3D, CyberBlade series i1, i7 (DSTN), i1, i1 (DSTN), Ai1, Ai1 (DSTN), CyberBlade/e4, CyberBladeXP, CyberBladeAi1/XP, BladeXP
    Image
    3DImage975, 3DImage985, Cyber9520, Cyber9525, Cyber9397, Cyber9397DVD
    ProVidia
    9682, 9685, Cyber9382, Cyber9385, Cyber9388
    TGUI
    9440AGi, 9660, 9680
    ISA/VLBus
    8900C, 8900D, 9000, 9200CXr, Cyber9320, 9400CXi, 9440AGi These cards have been ported but need further testing and may not work.
     

    CONFIGURATION DETAILS

    Please refer to xorg.conf(5x) for general configuration details. This section only covers configuration details specific to this driver.

    The following driver Options are supported:

    Option N'34'SWCursorN'34' N'34'booleanN'34'
    Enable or disable the SW cursor. Default: off.
    Option N'34'NoAccelN'34' N'34'booleanN'34'
    Disable or enable acceleration. Default: acceleration is enabled.
    Option N'34'PciRetryN'34' N'34'booleanN'34'
    Enable or disable PCI retries. Default: off.
    Option N'34'CyberShadowN'34' N'34'booleanN'34'
    For Cyber chipsets only, turn off shadow registers. If you only see a partial display - this may be the option for you. Default: on.
    Option N'34'CyberStretchN'34' N'34'booleanN'34'
    For Cyber chipsets only, turn on stretching. When the resolution is lower than the LCD's screen, this option will stretch the graphics mode to fill the entire LCD. Default: off.
    Option N'34'ShadowFBN'34' N'34'booleanN'34'
    Enable or disable use of the shadow framebuffer layer. Default: off.
    Option N'34'VideoKeyN'34' N'34'integerN'34'
    This sets the default pixel value for the YUV video overlay key. Default: undefined.
    Option N'34'TVChipsetN'34' N'34'stringN'34'
    This sets the TV chipset. Options are CH7005 or VT1621. Default: off.
    Option N'34'TVSignalN'34' N'34'integerN'34'
    This sets the TV signalling. Options are 0 for NTSC or 1 for PAL. Default: undefined.
    Option N'34'NoPciBurstN'34' N'34'booleanN'34'
    Turn off PCI burst mode, PCI Bursting is on by default. Default: off.
    Option N'34'XvHsyncN'34' N'34'integerN'34'
    Override the default Horizontal-sync value for the Xv extension. This is used to center the Xv image on the screen. By default the values are assigned based on the video card. Default: 0.
    Option N'34'XvVsyncN'34' N'34'integerN'34'
    Override the default Vertical-sync value for the Xv extension. This is used to center the Xv image on the screen. By default the values are assigned based on the video card. Default: 0.
    Option N'34'XvBskewN'34' N'34'integerN'34'
    Override the default Bottom skew value for the Xv extension. This is used to extend the Xv image on the screen at the bottom. By default the values are assigned based on the video card. Default: 0.
    Option N'34'XvRskewN'34' N'34'integerN'34'
    Override the default Right skew value for the Xv extension. This is used to extend the Xv image on the screen at the right. By default the values are assigned based on the video card. Default: 0.
    Option N'34'DisplayN'34' N'34'stringN'34'
    Override the display. Possible values are N'34'CRTN'34', N'34'LCDN'34' and N'34'DualN'34'. Please note that this option is only experimentally. Default: Use display active when X started.
    Option N'34'Display1400N'34' N'34'booleanN'34'
    Inform driver to expect 1400x1050 display instead of a 1280x1024. Default: off.
    Option N'34'GammaBrightnessN'34' N'34'stringN'34'
    Set display gamma value and brightness. N'34'stringN'34' is N'34'gamma, brightnessN'34', where gamma is a floating point value greater than 0 and less or equal to 10. brightness is an integer value greater or equal to 0 and less than 128. Default: gamma and brightness control is turned off. Note: This is not supported on all chipsets. Option N'34'AccelMethodN'34' N'34'stringN'34' Choose acceleration architecture, either "XAA" or "EXA". XAA is the old (but stable) XFree86 based acceleration architecture. EXA is a newer and simpler acceleration architecture designed to better accelerate the X Render extension. Default: "XAA".
     

    SEE ALSO

    Xorg(1x), xorg.conf(5x), xorgconfig(1x), Xserver(1x), X(7)  

    AUTHOR

    Author: Alan Hourihane, EXA for Blade chips by Jesse Barnes


     

    Index

    NAME
    SYNOPSIS
    DESCRIPTION
    SUPPORTED HARDWARE
    CONFIGURATION DETAILS
    SEE ALSO
    AUTHOR


    Поиск по тексту MAN-ов: 



      Закладки на сайте
      Проследить за страницей
    Created 1996-2017 by Maxim Chirkov  
    ДобавитьРекламаВебмастеруГИД  
    Hosting by Ihor