Date: Tue, 22 Dec 1998 13:39:30 -0800
From: John Bashinski <jbash@CISCO.COM.>
To: BUGTRAQ@NETSPACE.ORG
Subject: Update on Cisco IOS 12.0 security bug
-----BEGIN PGP SIGNED MESSAGE-----
This is an update for a message I sent about 5 hours ago.
Changes from the earlier message:
1. We've found more affected versions. In addition to all 12.0 variants,
11.3AA and 11.3DB are affected. Plain old 11.3 is *not* affected.
Neither is, 11.3T, or any of the other 11.3 variants we've
looked at. We now know where the bug was introduced, and it's
unlikely that that code has made its way into any releases other
than 11.3AA, 11.3DB, and the 12.0 variants. When our Sydney office
wakes up, we'll be able to make some final checks.
2. I left out the bug ID in the last message. It's CSCdk77426.
3. The workaround text mentions broadcast addresses.
We still don't have fix dates; it can take some time to get fixes
through the release process. When we have fix dates, we'll do
a formal notice.
Amended message follows--
We've had a report of nmap UDP scans crashing Cisco routers running
Cisco IOS software version 12.0. This was mentioned on BUGTRAQ, which
has a very wide distribution. It would be very easy to exploit.
Administrators should be on the lookout for potential exploitation of
this bug.
We've verified that the problem does exist. We believe that it affects
all Cisco routers running any variant of 12.0 (including 12.0T, 12.0S,
etc.). 11.3AA and 11.3DB are also affected. Mainline 11.3 and 11.3T are
not affected. None of the other 11.3 variants that we've checked are
affected. Because of where the problem was introduced, we think that
11.3AA and 11.3DB are almost certainly the only affected 11.3
variants. We will continue to check other 11.3 variants, and will issue
another update if any turn up affected.
The problem appears to be caused by packets sent to the router's syslog
port (UDP port 514). A tested workaround is to use an access list to
block incoming syslog traffic. You'd do this with something like this:
! Deny all multicasts to port 514
access-list 101 deny udp any 224.0.0.0 31.255.255.255 eq 514
! Deny old-style broadcasts
access-list 101 deny udp any host 0.0.0.0 eq 514
! Deny network-specific broadcasts (*example*; depends on local netmasks)
access-list 101 deny udp any 192.31.7.255 eq 514
! Deny router's own addresses
access-list 101 deny udp any host <router-addr-1> eq 514
access-list 101 deny udp any host <router-addr-2> eq 514
access-list 101 deny udp any host <router-addr-3> eq 514
... etc ...
access-list 101 permit ip any any
interface <interface-1>
ip access-group 101 in
interface <interface-2>
ip access-group 101 in
... etc ...
The access list needs to block syslog traffic destined for any of the
router's own IP addresses, or for any broadcast or multicast address on
which the router may be listening. Don't forget to block all-zeroes
broadcasts as well as all-ones broadcasts. It should be applied on
all interfaces running IP, including virtual interfaces and
subinterfaces (but not loopback interfaces).
This workaround *does* have a performance impact that may be significant
for some users. The impact isn't usually extreme, but it may make a
difference on a router that's already heavily loaded. Install it with
care if you install it.
This bug may cause different router platforms to crash differently.
Some routers have been observed to reboot and claim that they
were "restarted by power-on"; you won't necessarily get a stack
trace from one of these crashes.
Since this is still not completely characterized, and since we do not
yet have any reports of exploitation, you may choose to hold the
workaround in reserve and apply it only if you believe you are being
attacked. We should have a formal notice with full details within the
next few days. We cannot yet make any estimate of when a fix will be
available; we should have more information by the time the formal notice
comes out.
If you find that you are actually attacked with this, please report
the attack to Cisco at "security-alert@cisco.com".
For more information on Cisco security procedures, see
http://www.cisco.com/warp/customer/791/sec_incident_response.shtml
-- J. Bashinski
Cisco Systems
-----BEGIN PGP SIGNATURE-----
Version: 2.6.3in
Charset: noconv
iQEVAwUBNoARckZi51ggEbh5AQEVlwf9EKP5iPzwfp4UpxsN1nnqLscyrLYYKXIs
ce/EMcQP7znbkmse6cSFz5nOIKQpRl+c+rxLg8V3oeGTEriIyOA/jR0oVeU2Nn4N
rS6daaorZU1ngGhZ4zTRYNoGbGOU4EjwnU/wJV1yrrIuLA3EAHz+67kT90qSRJy7
R8ny+0tbtu7ZFdHI9Ccokal59HOz+Gbt29ep5/Ft0REVFoRqJCphJP06bT2HLIXZ
qLXPBErmVc9fP0wqdf11tbc3zaiytBbVn6is9sFdqod14KeiBblOC99vfM7OG1KY
rh3pLqSeLs76sw4RZycXAQWdLiY3Xgx3ZFwhB0YrpzUJnXGEDbcb7Q==
=Xp1o
-----END PGP SIGNATURE-----
